Embed Size (px)
DESCRIPTION
Package Status • 2015-07-10: IPA04 is released in Rev. A.2 Package Information2.1 General InformationThis is a scheduled package for MSC 13A that consists of APT/APZ ACs, and APT/APZ RPs.To see a list of all Trouble Reports and the list of all included packages, please see the Package Description (PDE) which is part of the package content delivered via Software Gateway.IPA04 includes the APZ19.0 ICM906, ICM907, ICM908 and ICM909 level.IPA04 is an accumulated package. It includes also IPA01, IPA02, IPA03and EPAs 1, 2, 3, 6, 7, 10, 12, 13, 16, 19, 20, 21, 22, 23, 25, 28, 29, 34, 35, 36, 37, 38, 40, 46, 49, 52, 56, 58, 59, 60, 61, 63, 66, 68, 71, 72, 73, 74,76,79, 81, 82, 84, 85, 86, 87, 88, 91 and 92 meaning that user has the option to select the packages to be implemented. The available options are:- IPA04 only- IPA04 (only or with any combination of EPAs)- IPA03 (only or with any combination of EPAs)- IPA02 (only or with any combination of EPAs)- IPA01 (only or with any combination of EPAs)- EPAs (without selecting any IPA)In case user selects IPA04 package to be implemented then all previous released EPAs packages will be selected also for loading. For further information about the Packages dependency, please refer to the Package_Contents_MSC13A_MSC13AUP_BJ document, Package_dependency sheet, placed in the DOC folder of the package.In case user selects for implementing a package that does not deliver APZ ACs then no APZ loadfile will be created. The user during the cp_script execution should ignore the Fault Code 8 on the IOCMI command for the APZ loadifles and should press APPLY to continue with the script execution. A popup window will appear saying that “Command file does not exist, execute correct file manually, and then press APPLY “(for example 13A5I000AL01.COR and 13A5I000AS01.COR in case the APZ type of the node is APZ21250).IPA04 does not include any MW software. Though, there are EPA93 (21403 latest MW), EPA100 (21250 latest MW) and EPA115 (21260 latest MW) included in the Accumulation. Important information:• IPA04 uses only the cloning method on BC nodes.• In case of MSC-BC system, the apg_update script will be executed only for blade and not for SPXs.• SPX only: A large restart will be issued in SPXs in order to clear corruptions after IPA03 loading. That restart will not happen at the same time to both SPXs. So the traffic impacts will be minimal.IPA04 includes several solutions which require special handling, for further information, please refer to chapter 3.3 Implementation Warnings. IPA04 can be loaded using the Unattended Update feature. Further documentation on this feature is provided in the DOC folder of the package. 2.2 Applicability This package is applicable to the following configurations. However, pleasenote that PLM has not tested all possible configurations.MSC Release: MSC 13ASignaling Standard: ETSI, ANSI, TTC, CWTSNode type: MSC, MSC-BCAPZ: APZ21250, APZ21260, APZ21403IO: APG40, APG43 OSS RC: 13.0 and onwards2.3 Applicable Base Levels The minimum base level for this package is GA. 2.4 Signaling Standard VerificationNOTE: Please be aware that the package may not have been verified in all signaling standards.ETSI: NOT Verified.ANSI: NOT Verified.CWTS: NOT Verified.TTC: NOT Verified.This package is SEA verified at the moment. Though, there will take place ETSI verification in the future.2.5 Reference to Write a Trouble Report on this PackageIn order to issue a Trouble Report on this package, please use the following references: Traffic Impacting Warnings No traffic impacting warnings were observed during package implementation.3.5 Manual HandlingIn case any manual activity is needed, it should be performed using an extracommand handling terminal. Manual intervention might be necessary in a faultsituation or to perfor
Citation preview
APLICAÇÃO DO EPA-115 NOS APZ21260.
1º. Antes de começar a atividade deve alterar o usuário OSSUSER para grupo de admin.
2º Acessar a Plataforma do Upgrade de Centrais.
3º Na guia software selecionar o pacote MSC13A UPDATE PACKAGE BH, selecionar para
upgrade.
4º selecionar o elemento para criação da JOB
5º Selecionar todas as opções para a execução da atividade, o start mode pode ficar conforme
a necessidade de cada operador, manual ou imediato, pode ser feito tudo a noite pois é
pequeno a atualização, ou executar durante o dia até a parte do download. E o restando a
noite, pode também ser criado uma Job até o download e outra a partir do cp, ou uma única
contendo todos as funções com a opção de imediato até o download e o restante manual para
ser executado em partes. Aqui vai do gosto do operador.
Aqui não é necessário alteração de parâmetros
6º Nesta etapa deve-se dar um nome para o Upgrade
7º próxima etapa selecionar o job criado anteriormente e inicial o processo PKG_SELECTION
Visualizar a execução do processo clicando em Start OPS GUI
Abaixo mensagem informativa, clicar em Apply
Mensagem informando os pacotes presentes e instalado anteriormente. Clicar em Apply
Aqui Selecionar somente o EPA-115 aplicável no APZ 21260 e nas SPX no caso das Blades.
Mensagem confirmando a aplicação do Pacote, selecionar Yes e Apply.
Mensagem informativa, apenas clicar em Apply
Final do processo PKG_SELECTION
8º Iniciar o processo NSLOPE
Execução do processo.
Final do processo NSLOPE
9º Iniciar processo APG Software Update
Processo em execução.
Final do processo APG Software Upgrade.
10º. Iniciar processo Heath Check
Visualizar execução do processo
Final do processo Heath Check
11º. Iniciar processo de Download
Visualizar execução do processo
Fim do processo Download
12º O processo de CP deve ser executado a noite.
13º Iniciar o processo CP para continuar o upgrade.
Tela informativa de alarmes
Tela informativa clicar em Apply
Tela informativa sobre a separação do CP, clicar em Apply
Tela informando que o CP-a era o CP-EX, e pergunta quero deixar como estava antes, colocar Y
e clicar em Apply
Fim da execução do processo do CP
14º Iniciar o Processo de limpeza CleanUP
Atividade concluída.
15º. Após o termino da atividade remover o usuário OSSUSER do grupo de admin.
