Upload
felipe-lima
View
292
Download
3
Embed Size (px)
Citation preview
MULTI-LINE 2 Lista de Parâmetros
Controle Automático Do Gerador AGC
Versão do Software 3.3x.x
Document no.: 4189340563A
•� Lista de Alarmes
•� Lista de Par�metros
AGC-3 Alarm and Parameter List
DEIF A/S Page 2 of 112
Tabela de conteúdo
1. SOBRE ESTE MANUAL .................................................................................................... 5 PROPOSTA GERAL ....................................................................................................................... 5 USUÁRIOS ESPECÍFICOS .............................................................................................................. 5 SUMÁRIO/ESTRUTURA GERAL....................................................................................................... 5
2. AVISOS E INFORMAÇÃO LEGAL .................................................................................... 6 INFORMAÇÃO LEGAL E RESPONSABILIDADE ................................................................................... 6 AVISO SOBRE DESCARGA ELETROSTÁSTICA .................................................................................. 6 QUESTÕES DE SEGURANÇA.......................................................................................................... 6 DEFINIÇÕES................................................................................................................................. 6
3. LISTA DE ALARMES......................................................................................................... 7 TABELAS DE ALARMES ................................................................................................................. 8 PROTEÇÕES DE POTÊNCIA REVERSA E SOBRECORRENTE. .......................................................... 11 PROTEÇÃO DE TENSÃO.............................................................................................................. 14 PROTEÇÕES DE FREQUÊNCIA. .................................................................................................... 16 PROTEÇÕES DE TENSÃO NO BARRAMENTO.................................................................................. 18 PROTEÇÃO DE FREQUÊNCIA NOBARRAMENTO ............................................................................. 20 PROTEÇÃO DE FALHA DE REDE ................................................................................................... 22 PROTEÇÃO DE SOBRECARGA...................................................................................................... 23 PROTEÇÃO CONTRA DESBALANCEAMENTO DE CORRENTE ............................................................ 25 PROTEÇÃO CONTRA DESBALANCEAMENTO DE TENSÃO................................................................. 25 PROTEÇÃO CONTRA IMPORTAÇÃO DE POTÊNCIA REATIVA (PERDA DE EXCITAÇÃO). ........................ 26 PROTEÇÃO CONTRA EXPORTAÇÃO DE POTÊNCIA REATIVA (SOBRE EXCITAÇÃO). ............................ 26 SEQUENCIA NEGATIVA ................................................................................................................ 27 SEQUÊNCIA ZERO ...................................................................................................................... 27 PROTEÇÃO CONTRA SOBRECORRENTE DIRECIONAL ..................................................................... 28 DESBALANCEAMENTO DE TENSÃO DO BARRAMENTO. ................................................................... 29 SINCRONIZAÇÃO E ALARMES DOS DISJUNTORES. ......................................................................... 29 ALARMES DOS REGULADORES .................................................................................................... 33 PROGRAMAR ENTRADA DIGITAL 23-27........................................................................................ 34 PROGRAMAR ENTRADA DIGITAL 43-55........................................................................................ 34 PROGRAMAR ENTRADA DIGITAL 91-97........................................................................................ 35 PROGRAMAR ENTRADA DIGITAL 102-108.................................................................................... 35 DIGITAL INPUT 112-117 SETUP ................................................................................................... 36 PARADA DE EMERGENCIA ........................................................................................................... 37 PROGRAMAR ENTRADA DIGITAL 127-133.................................................................................... 37 PROGRAMAR ENTRADA ANALÓGICA (OPÇÃO M15.6).................................................................... 38 PROGRAMAR ENTRADA ANALÓGICA MULTI-FUNCTIONAL .............................................................. 41 PROGRAMAR VELOCIDADE E FEEDBACK DE FUNCIONAMENTO ....................................................... 51 PROGRAMAR ALIMENTAÇÃO ....................................................................................................... 53 ALARMES DE COMUNICAÇÃO INTERNA E FIO DESCONECTADO DA SOLENÓIDE DE PARADA ........... 55 FALHA DE AQUECIMENTO DO MOTOR ......................................................................................... 55 TESTE DE BATERIA .................................................................................................................... 56 MAXIMA VENTILAÇÃO ................................................................................................................. 57 ERRO SWITCHBOARD ................................................................................................................. 58 ERRO SWITCHBOARD ................................................................................................................. 58 ERRO DE COMUNICAÇÃO EXTERNA ............................................................................................ 59 ALARMES DE COMUNICAÇÃO DE INTERFACE DO MOTOR ............................................................. 60 ERRO DE COMUNICAÇÃO DO GERENCIADOR DE POTÊNCIA ......................................................... 63 ERRO DE COMUNICAÇÃO INTERNA CAN ..................................................................................... 64 PROGRAMAR ALARME DE I/O EXTERNO ...................................................................................... 64
AGC-3 Alarm and Parameter List
DEIF A/S Page 3 of 112
4. LISTA DE PARÂMETROS............................................................................................... 66 TABELA DE PARÂMETROS .......................................................................................................... 66 SINCRONIZAÇÃO ........................................................................................................................ 69 REGULADORES .......................................................................................................................... 70 PROGRAMAR SAÍDA DIGITAL ....................................................................................................... 76 LIMITE DE SAÍDA ANALÓGICA...................................................................................................... 79 SAÍDA DE TRANSDUTORES ......................................................................................................... 80 SELEÇÃO DO REGULADOR DE SAÍDA .......................................................................................... 84 SISTEMA .................................................................................................................................... 84 PROGRAMAÇÃO GERAL .............................................................................................................. 85 CONTADORES E RELÓGIOS......................................................................................................... 86 ALARME CIRENE ........................................................................................................................ 87 FUNCIONAMENTO, PARTIDA E PARADA ........................................................................................ 88 CONTROLE DO DISJUNTOR......................................................................................................... 89 TAXA DE DECREMENTO.............................................................................................................. 89 PARTIDA EM MARCHA LENTA ...................................................................................................... 90 AQUECIMENTO DO MOTOR ......................................................................................................... 90 LINHAS DE SAÍDA DO DIVISOR DE CARGA ANALÓGICO ................................................................ 90 TEMPORIZADOR ......................................................................................................................... 91 VENTILADOR DE RESFRIAMENTO ................................................................................................ 91 PARTIR/PARAR PRÓXIMO GERADOR ........................................................................................... 91 BOMBA DE COMBUSTÍVEL........................................................................................................... 92 HORÁRIO DE VERÃO .................................................................................................................. 92 PROGRAMAR REDE .................................................................................................................... 93 TESTE ....................................................................................................................................... 93 CONTROLE DE CONFIGURAÇÃO .................................................................................................. 94 FALHA DE REDE ........................................................................................................................ 94 MODO DE FALHA CAN............................................................................................................... 96 COMUNICAÇÃO EXTERNA............................................................................................................ 96 COMUNICAÇÃO INTERNA DO POWER MANAGEMENT .................................................................... 98 COMUNICAÇÃO DE INTERFACE DO MOTOR.................................................................................. 98 PROGRAMAR COMUNICAÇÃO DE I/O EXTERNO ............................................................................ 99 IMPRIMIR EVENTOS .................................................................................................................... 99 PROGRAMAR GERENCIADOR DE POTÊNCIA ............................................................................... 100 JUMP MENUS............................................................................................................................ 105 COMANDOS DE HORÁRIO ......................................................................................................... 107 CONFIGURAÇÃO GSM.............................................................................................................. 108 SENHAS................................................................................................................................... 108 VDO 102 ................................................................................................................................ 109 VDO 105 ................................................................................................................................ 110 VDO 108 ................................................................................................................................ 111 SELECIONAR MULTI-ENTRADAS................................................................................................. 111 SAÍDAS DIGITAIS EXTERNA ....................................................................................................... 112 STATUS DO MÓDULO EXTERNO ................................................................................................ 112
AGC-3 Alarm and Parameter List
DEIF A/S Page 4 of 112
Este documento é válido para os seguintes produtos: AGC Software versão 3.3X.X ou depois.
AGC-3 Alarm and Parameter List
DEIF A/S Page 5 of 112
1. Sobre este Manual Este capítulo inclui informações gerais para o usuário sobre este manual referente à proposta geral, os usuários, conteúdo e estrutura geral.
Proposta Geral Este documento é uma lista completa de parâmetros para DEIF's Multi-line unidades com software ver. 3. O documento inclui todos os parâmetros, o que significa que alguns dos parâmetros incluídos opção pode não ser acessível no sistema em questão.
Usuários Específicos O lista parâmetro é destinada principalmente para as pessoa responsáveis pela unidade configuração de parâmetro. Todos os usuários podem também encontrar outras informações úteis aqui.
Sumário/Estrutura Geral A lista de parâmetros é dividido em capítulos e, a fim de tornar a estrutura do documento simples e fácil de usar, cada capítulo terá início a partir do início de uma nova página. O seguinte irá descrever o conteúdo de cada um dos capítulos.
Sobre este manual Este primeiro capítulo inclui informações gerais sobre este manual como um documento. Trata-se da finalidade geral e os usuários da lista de parâmetros. Além disso, descreve o conteúdo e a estrutura do documento.
Avisos e informação Legal O segundo capítulo inclui informações gerais sobre questões jurídicas relevantes e precauções de segurança no manuseio de produtos DEIF. Além disso, este capítulo irá apresentar nota e símbolos de aviso, que será utilizado ao longo de todo o manual.
Programar Processo De Parâmetros Este capítulo aborda o procedimento a ser seguido, quando os parâmetros são criados ou alterados. Através da utilização de diversas ilustrações deste capítulo irá guiar o usuário através do processo de parâmetro configuração passo a passo.
Lista De Alarmes Este capítulo inclui uma lista completa alarme padrão para instalação. Assim, este capítulo deve ser utilizado como referência, quando a informação específica sobre alarmes é necessária.
Lista De Parâmetros Este capítulo inclui uma completa lista de parâmetros para configuração padrão. Assim, este capítulo deve ser utilizado como referência, quando informações sobre parâmetros específicos é necessário.
AGC-3 Alarm and Parameter List
DEIF A/S Page 6 of 112
2. Avisos e Informação Legal Este capítulo inclui informações importantes sobre questões jurídicas relevantes geral na manipulação de produtos DEIF. Além disso, algumas precauções de segurança global será introduzido e recomendado. Por fim, destacam-se as notas e avisos, que serão utilizados ao longo deste manual, estão sendo apresentados.
Informação Legal e Responsabilidade A DEIF não se responsabiliza pela instalação ou operação dos geradores. Se houver qualquer dúvida quanto à instalação ou operação do gerador controlado pela unidade, deve ser contatada a companhia responsável pela instalação ou operação do instrumento
Aviso sobre descarga Eletrostástica Os terminais devem ser protegidos contra descargas eletrostáticas durante a instalação, uma vez instalada e conectada a unidade, estas precauções não serão mais necessárias.
Questões de Segurança A instalação deve ser feita apenas por funcionários autorizados, cientes dos riscos que envolvem trabalhar com equipamentos elétricos.
Definições Ao decorrer do manual várias notas e avisos serão apresentados. Para garantir que serão notados, serão destacados do texto.
Notas
Avisos
As notas facilitam a memorização das informações gerais pelo leitor.
Os avisos indicam uma situação potencialmente perigosa que pode resultar em morte, ferimentos ou danos ao equipamento se tais precauções não forem seguidas.
Atenção com correntes e voltagens. Não tocar entradas para medição AC, risco letal.
As unidades não devem ser abertas por funcionários não autorizados. Caso contrário, a garantia será perdida.
AGC-3 Alarm and Parameter List
DEIF A/S Page 7 of 112
3. Lista De Alarmes Este capítulo inclui uma lista completa alarme, incluindo todas as opções possíveis. Assim, este capítulo deve ser utilizado como referência quando as informações específicas sobre os vários parâmetros são necessários para a configuração do aparelho. Uma lista panorâmica pode ser vista na próxima página. O tabela é constituída pelos seguintes ajustes possíveis: Setpoint: O alarme setpoint é ajustado no menu setpoint. A definição é uma percentagem
do valor nominal. Delay: A configuração do temporizador é o tempo que deve expirar o alarme se o nível
for atingido até que o alarme ocorra. Relay output A: Um relé de saída pode ser ativada pela saída A. Relay output B: Um relé de saída pode ser ativada pela saída B. Enable: O alarme pode ser ativado ou desativado. ON significa sempre ativado, RUN significa que o alarme tenha status de funcionamento. Isto significa que é ativado quando o sinal de funcionamento está presentes. Fail class: Quando o alarme ocorre a unidade irá reagir dependendo da classe de falha
selecionada. Fail classes are:
Classe De Falha
DG (Gerador Diesel)
Unidade De Rede
BTB (Disjuntor Bus Tie )
1 Block Block Block 2 Warning Warning Warning 3 Trip GB Trip TB Trip BTB 4 Trip + Stop Trip MB N/A 5 Shutdown N/A N/A 6 Safety stop N/A N/A 7 N/A N/A N/A
No seguinte, estas abreviações são usadas: G: Gerador GB: Disjuntor Do Gerador TB: Disjuntor Tie (Para Unidade De Rede) MB: Disjuntor De Rede BTB: Disjuntor Bus tie BA: Barramento A (Unidade BTB) BB: Barramento (Unidade BTB: Barramento B) N/A: Não Disponível
AGC-3 Alarm and Parameter List
DEIF A/S Page 8 of 112
Também é possível configurar os parâmetros, usando o PC utility software. Será possível fazer as mesmas configurações como descrito acima. Ao utilizar o PC utility software, a funcionalidade extra está disponível. Para todas as proteções que é possível fazer um reconhecimento automático do alarme.
Tabelas De Alarmes Proteção Programar Entradas Multi-analógicas 1000 G/M/BA -P> 1 4120 4-20mA 102.1 1010 G/M/BA -P> 2 4130 4-20mA 102.2 1030 G/M/BA I> 1 4140 V DC 102.1 1040 G/M/BA I> 2 4150 V DC 102.2 1050 G/M/BA I> 3 4160 PT 102.1 1060 G/M/BA I> 4 4170 PT 102.2 4180 VDO oil 102.1 1130 G/M/BA I>> 1 4190 VDO oil 102.2 1140 G/M/BA I>> 2 4200 VDO water 102.1 1150 G/M/BA U> 1 4210 VDO water 102.2 1160 G/M/BA U> 2 4220 VDO fuel 102.1 1170G/M/BA U< 1 4230 VDO fuel 102.2 1180 G/M/BA U< 2 4240 W. fail 102 1190 G/M/BA U< 3 4250 4-20mA 105.1 1200 G/M/BA voltage trip 4260 4-20mA 105.2 1210 G/M/BA f> 1 4270 V DC 105.1 1220 G/M/BA f> 2 4280 V DC 105.2 1230 G/M/BA f> 3 4290 PT 105.1 1240 G/M/BA f< 1 4300 PT 105.2 1250 G/M/BA f< 2 4310 VDO oil 105.1 1260 G/M/BA f< 3 4320 VDO oil 105.2 1270 BB U> 1 4330 VDO water 105.1 1280 BB U> 2 4340 VDO water 105.2 1290 BB U> 3 4350 VDO fuel 105.1 1300 BB U< 1 4360 VDO fuel 105.2 1310 BB U< 2 4370 W. fail 105 1320 BB U< 3 4380 4-20mA 108.1 1330 BB U< 4 4390 4-20mA 108.2
Pequenas diferenças devido à natureza dos parâmetros podem existir entre as tabelas individuais.
AGC-3 Alarm and Parameter List
DEIF A/S Page 9 of 112
1340 BB Voltage trip 4400 V DC 108.1 1350 BB f> 1 4410 V DC 108.2 1360 BB f> 2 4420 PT 108.1 1370 BB f> 3 4430 PT 108.2 1380 BB f< 1 4440 VDO oil 108.1 1390 BB f< 2 4450 VDO oil 108.2 1400 BB f< 3 4460 VDO water 108.1 1410 BB f< 4 4470 VDO water 108.2 1420 df/dt (ROCOF) 4480 VDO fuel 108.1 1430 Vector jump 4490 VDO fuel 108.2 1440 BB pos seq volt 4500 W. fail 108 1450 G/M/BA P> 1 4510 Overspeed 1 1460 G/M/BA P> 2 4520 Overspeed 2 1470 G/M/BA P> 3 4530 Crank failure 1480 G/M/BA P> 4 4540 Run feedb. fail 1490 G/M/BA P> 5 4550 MPU wirebreak 1500 G/M Unbalance current 4560 Hz/V failure 1510 G/M Unbalance volt 4570 Start failure 1520 G/SG/SC/BA -Q> 4580 Stop failure 1530 G/SG/SC/BA Q> 1540 G/M Neg. Seq. current 4960 U< aux. term. 1 1550 G/M Neg. seq. voltage 4970 U> aux. term. 1 1560 Neg. seq. select 4980 U< aux. term.98 1570 G/M/BA zero seq. current 4990 U> aux. term.98 1580 G/M/BA zero seq. Voltage 1590 Zero seq. Select Sistema 1600 G/M/BA Directional overcurrent 1 - Programar Gerador 1610 G/M/BA Directional overcurrent 2 6270 Stop coil wire fail 1620 BB Unbalance U 6280 Int. comm. fail Controle 6330 Engine heater 1 - Sincronização 2120 Sync window 6410 Battery test 2130 GB/TB/BTB sync failure 6420 Auto battery test 2140 MB sync failure 6430 Battery asymmetry 2150 Phase seq error 6440 Battery asymmetry 1 2160 GB/TB/BTB open fail 6450 Battery asymmetry 2 2170 GB//TB/BTB close fail 2180 GB/TB/BTB pos. fail 6470 Max ventilation 1 2200 MB open fail 6480 Max ventilation 2 2210 MB close fail 2220 MB pos. fail 6500 Blk. Swbd error 6510 Stp. Swbd error 2270 Close before excitation fail 6540 Not in Auto - Reguladores 2560 GOV reg. fail Sistema 2630 Deload error - Comunicação 2680 AVR reg. fail 7520 Ext. Comm. Error 7530 CAN fail mode Entradas/Saídas - Programar Entradas Binárias 7570 EI comm. Error 3000 Dig input 23 7580 EIC warning 3010 Dig. input 24 7590 EIC shutdown 3020 Dig. input 25 7600 EIC overspeed 3030 Dig. input 26 7610 EIC coolant t. 1 3040 Dig. input 27 7620 EIC coolant t. 2 7630 EIC oil press. 1 3130 Dig. Input 43 7640 EIC oil press. 2 3140 Dig. Input 44 7650 EIC oil temp. 1 3150 Dig. Input 45 7660 EIC oil temp. 2 3160 Dig. Input 46 3170 Dig. Input 47 7870 Any BTB missing/appl Hazard 3180 Dig. Input 48 3190 Dig. Input 49 7930 CAN 1 Comm error
AGC-3 Alarm and Parameter List
DEIF A/S Page 10 of 112
3200 Dig. Input 50 7940 CAN 2 Comm error 3210 Dig. Input 51 3220 Dig. Input 52 - External I/O 3230 Dig. Input 53 12000 Ext. Ain 1.1 3240 Dig. Input 54 12010 Ext. Ain 1.2 3250 Dig. Input 55 12030 Ext. Ain 2.1 3330 Dig. Input 91 12040 Ext. Ain 2.2 3340 Dig. Input 92 3350 Dig. Input 93 12060 Ext. Ain 3.1 3360 Dig. Input 94 12070 Ext. Ain 3.2 3370 Dig. Input 95 3380 Dig. Input 96 12090 Ext. Ain 4.1 3390 Dig. Input 97 12100 Ext. Ain 4.2 3400 Dig. input 102 12120 Ext. Ain 5.1 3410 Dig. input 105 12130 Ext. Ain 5.2 3420 Dig. input 108 12150 Ext. Ain 6.1 3430 Dig. input 112 12160 Ext. Ain 6.2 3440 Dig. input 113 3450 Dig. input 114 12180 Ext. Ain 7.1 3460 Dig. input 115 12190 Ext. Ain 7.2 3470 Dig. input 116 3480 Dig. input 117 12210 Ext. Ain 8.1 12220 Ext. Ain 8.2 3490 Emergency stop 3500 Dig. input 127 3510 Dig. input 128 3520 Dig. input 129 12540 Ext dig. In 1 3530 Dig. input 130 12550 Ext dig. In 2 3540 Dig. input 131 12560 Ext dig. In 3 3550 Dig. input 132 12570 Ext dig. In 4 3560 Dig. input 133 12580 Ext dig. In 5 12590 Ext dig. In 6 12600 Ext dig. In 7 12610 Ext dig. In 8 12620 Ext dig. In 9 - Programar Entrada Analógica 12630 Ext dig. In 10 4000 4-20 mA 91.1 12640 Ext dig. In 11 4010 4-20 mA 91.2 12650 Ext dig. In 12 4020 W. fail ana 91 12660 Ext dig. In 13 4030 4-20 mA 93.1 12670 Ext dig. In 14 4040 4-20 mA 93.2 12680 Ext dig. In 15 4050 W. fail ana 93 12690 Ext dig. In 16 4060 4-20 mA 95.1 4070 4-20 mA 95.2 4080 W. fail ana 95 4090 4-20 mA 97.1 4100 4-20 mA 97.2 4110 W. fail ana 97
AGC-3 Alarm and Parameter List
DEIF A/S Page 11 of 112
Proteções de Potência Reversa e Sobrecorrente.
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1000 G/M/BA Potência Reversa 1
1001 G/M/BA –P> 1
Setpoint -110% 0%
-10.0%
1002 G/M/BA –P> 1
Delay 0.1 s 300.0 s
5.0 s
1003 G/M/BA –P> 1
Relay output A
Not used Option
dependent Not used
1004 G/M/BA –P> 1
Relay output B
Not used Option
dependent Not used
1005 G/M/BA –P> 1
Enable OFF ON
ON
1006 G/M/BA –P> 1
Fail class F1…F7 Trip GB (F3)
Designers Reference Handbook
O alarme e a classe de falha são ativados quando o valor de potência reversa passar o valor e o tempo programado.
1010 G/M/BA Potência Reversa 2
1011 G/M/BA –P> 2
Setpoint -110.0% 0.0%
-15.0%
1012 G/M/BA –P> 2
Delay 0.1 s 300.0 s
1.0 s
1013 G/M/BA –P> 2
Relay output A
Not used Option
dependent Not used
1014 G/M/BA –P> 2
Relay output B
Not used Option
dependent Not used
1015 G/M/BA –P> 2
Enable OFF ON
ON
1016 G/M/BA –P> 2
Fail class F1…F7 Trip GB (F3)
Designers Reference Handbook
O alarme e a classe de falha são ativados quando o valor de potência reversa passar o valor e o tempo programado.
1030 G/M/BA Sobrecorrente 1
1031 G/M/BA I> 1
Setpoint 50.0% 200.0%
120.0%
1032 G/M/BA I> 1
Delay 0.1 s 999.9 s
20.0 s
1033 G/M/BA I> 1
Relay output A
Not used Option
dependent Not used
1034 G/M/BA I> 1
Relay output B
Not used Option
dependent Not used
1035 G/M/BA I> 1
Enable OFF ON
ON
1036 G/M/BA I> 1
Fail class F1…F7 Trip GB (F3)
Designers Reference Handbook
O alarme e a classe de falha são ativados quando o valor de corrente passar o valor e o tempo programado.
AGC-3 Alarm and Parameter List
DEIF A/S Page 12 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1040 G/M/BA Sobrecorrente 2
1041 G/M/BA I> 2
Setpoint 50.0% 200.0%
120.0%
1042 G/M/BA I> 2
Delay 0.1 s 999.9 s
10.0 s
1043 G/M/BA I> 2
Relay output A
Not used Option
dependent Not used
1044 G/M/BA I> 2
Relay output B
Not used Option
dependent Not used
1045 G/M/BA I> 2
Enable OFF ON
ON
1046 G/M/BA I> 2
Fail class F1…F7 Trip GB (F3)
Designers Reference Handbook
O alarme e a classe de falha são ativados quando o valor de corrente passar o valor e o tempo programado
1050 G/M/BA Sobrecorrente 3
1051 G/M/BA I> 3
Setpoint 50.0% 200.0%
130.0%
1052 G/M/BA I> 3
Delay 0.1 s 999.9 s
3.0 s
1053 G/M/BA I> 3
Relay output A
Not used Option
dependent Not used
1054 G/M/BA I> 3
Relay output B
Not used Option
dependent Not used
1055 G/M/BA I> 3
Enable OFF ON
ON
1056 G/M/BA I> 3
Fail class F1…F7 Trip GB (F3)
Designers Reference Handbook
O alarme e a classe de falha são ativados quando o valor de corrente passar o valor e o tempo programado
1060 G/M/BA Sobrecorrente 4
1061 G/M/BA I> 4
Setpoint 50.0% 200.0%
140.0%
1062 G/M/BA I> 4
Delay 0.1 s 999.9 s
1.0 s
1063 G/M/BA I> 4
Relay output A
Not used Option
dependent Not used
1064 G/M/BA I> 4
Relay output B
Not used Option
dependent Not used
1065 G/M/BA I> 4
Enable OFF ON
ON
1066 G/M/BA I> 4
Fail class F1…F7 Trip GB (F3)
Designers Reference Handbook
O alarme e a classe de falha são ativados quando o valor de corrente passar o valor e o tempo programado
1130 G/M/BA Corrente De Curtocircuito 1
1131 G/M/BA I>> 1
Setpoint 150.0% 350.0%
200.0% Opção C1 Add-on
O alarme e a classe de falha são ativados
AGC-3 Alarm and Parameter List
DEIF A/S Page 13 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1132 G/M/BA I>> 1
Delay 0.0 s 100.0 s
0.5 s
1133 G/M/BA I>> 1
Relay output A
Not used Option
dependent Not used
1134 G/M/BA I>> 1
Relay output B
Not used Option
dependent Not used
1135 G/M/BA I>> 1
Enable OFF ON
OFF
1136 G/M/BA I>> 1
Fail class F1…F7 Trip GB (F3)
proteção quando o valor de corrente passar o valor e o tempo programado.
1140 G/M/BA Corrente De Curtocircuito 2
1141 G/M/BA I>> 2
Setpoint 50.0% 200.0%
300.0%
1142 G/M/BA I>> 2
Delay 0.1 s 100.0 s
0.2 s
1143 G/M/BA I>> 2
Relay output A
Not used Option
dependent Not used
1144 G/M/BA I>> 2
Relay output B
Not used Option
dependent Not used
1145 G/M/BA I>> 2
Enable OFF ON
OFF
1146 G/M/BA I>> 2
Fail class F1…F7 Trip GB (F3)
Opção C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de corrente passar o valor e o tempo programado.
AGC-3 Alarm and Parameter List
DEIF A/S Page 14 of 112
Proteção De Tensão
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1150 G/M/BA Sobretensão 1
1151 G/M/BA U> 1
Setpoint
100.0% 120.0%
105.0%
1152 G/M/BA U> 1
Timer 0.1 s 300.0 s
5.0 s
1153 G/M/BA U> 1
Relay A Not used Option dep.
Not used
1154 G/M/BA U> 1
Relay B Not used Option dep.
Not used
1155 G/M/BA U> 1
Enable OFF ON
OFF
1156 G/M/BA U> 1
Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de tensão passar o valor e o tempo programado.
1160 G/M/BA Sobretensão 2
1161 G/M/BA U> 2
Setpoint
100.0% 120.0%
115.0%
1162 G/M/BA U> 2
Timer 0.1 s 300.0 s
1.0 s
1163 G/M/BA U> 2
Relay A Not used Option dep.
Not used
1164 G/M/BA U> 2
Relay B Not used Option dep.
Not used
1165 G/M/BA U> 2
Enable OFF ON
OFF
1166 G/M/BA U> 2
Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de tensão passar o valor e o tempo programado.
1170 G/M/BA Subtensão 1
1171 G/M/BA U< 1
Setpoint
80.0% 100.0%
95.0%
1172 G/M/BA U< 1
Timer 0.1 s 100.0 s
5.0 s
1173 G/M/BA U< 1
Relay A Not used Option dep.
Not used
1174 G/M/BA U< 1
Relay B Not used Option dep.
Not used
1175 G/M/BA U< 1
Enable OFF ON
OFF
1176 G/M/BA U< 1
Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de tensão baixar o valor e passar o tempo programado.
1180 G/M/BA Subtensão 2
1181 G/M/BA U< 2
Setpoint
50.0% 100.0%
80.0% Opção A1/A2/A3/B1/
O alarme e a classe de falha são ativados
AGC-3 Alarm and Parameter List
DEIF A/S Page 15 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1182 G/M/BA U< 2
Timer 0.1 s 100.0 s
3.0 s
1183 G/M/BA U< 2
Relay A Not used Option dep.
Not used
1184 G/M/BA U< 2
Relay B Not used Option dep.
Not used
1185 G/M/BA U< 2
Enable OFF ON
OFF
1186 G/M/BA U< 2
Fail class
F1…F7 Warning (F2)
C1 Add-on proteção
quando o valor de tensão baixar o valor e passar o tempo programado.
1190 G/M/BA Subtensão 3
1191 G/M/BA U< 3
Setpoint
50.0% 100.0%
70.0%
1192 G/M/BA U< 3
Timer 0.1 s 100.0 s
1.0 s
1193 G/M/BA U< 3
Relay A Not used Option dep.
Not used
1194 G/M/BA U< 3
Relay B Not used Option dep.
Not used
1195 G/M/BA U< 3
Enable OFF ON
OFF
1196 G/M/BA U< 3
Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de tensão baixar o valor e passar o tempo programado.
1200 G/M/BA Tipos De Medição
1201 G/M/BA Voltage trip
Setpoint
Ph-Ph Ph-N
Ph-Ph Opção A1/A2/A3/B1/ C1 Add-on
proteção
Selecionar Detecção de tensão entre fase-fase ou fase-neutro.
AGC-3 Alarm and Parameter List
DEIF A/S Page 16 of 112
Proteções de Frequência.
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1210 G/M/BA Sobrefrequencia 1
1211 G/M/BA f> 1
Setpoint 100.0% 120.0%
105.0%
1212 G/M/BA f> 1
Timer 0.2 s 100.0 s
3.0 sec
1213 G/M/BA f> 1
Relay A
Not used
Option dep.
Not used
1214 G/M/BA f> 1
Relay B
Not used
Option dep.
Not used
1215 G/M/BA f> 1
Enable OFF ON
OFF
1216 G/M/BA f> 1
Fail class F1…F7 Warning (F2)
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de frequência passar o valor e o tempo programado.
1220 G/M/BA Sobrefrequencia 2
1221 G/M/BA f> 2
Setpoint 100.0% 120.0%
105.0%
1222 G/M/BA f> 2
Timer 0.2 s 100.0 s
5.0 sec
1223 G/M/BA f> 2
Relay A
Not used
Option dep.
Not used
1224 G/M/BA f> 2
Relay B
Not used
Option dep.
Not used
1225 G/M/BA f> 2
Enable OFF ON
OFF
1226 G/M/BA f> 2
Fail class F1…F7 Warning (F2)
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de frequência passar o valor e o tempo programado.
1230 G/M/BA Sobrefrequencia 3
1231 G/M/BA f> 3
Setpoint 100.0% 120.0%
110.0%
1232 G/M/BA f> 3
Timer 0.2 s 100.0 s
1.0 sec
1233 G/M/BA f> 3
Relay A
Not used
Option dep.
Not used
1234 G/M/BA f> 3
Relay B
Not used
Option dep.
Not used
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de frequência passar o valor e o tempo programado.
As proteções de frequência são sobre as configurações nominais de frequência
AGC-3 Alarm and Parameter List
DEIF A/S Page 17 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1235 G/M/BA f> 3
Enable
Not used
Option dep.
Not used
1236 G/M/BA f> 3
Fail class F1…F7 Warning (F2)
1240 G/M/BA Subfrequencia 1
1241 G/M/BA f< 1
Setpoint 80.0% 100.0%
95.0%
1242 G/M/BA f< 1
Timer 0.2 s 100.0 s
5.0 sec
1243 G/M/BA f< 1
Relay A
Not used
Option dep.
Not used
1244 G/M/BA f< 1
Relay B
Not used
Option dep.
Not used
1245 G/M/BA f< 1
Enable OFF ON
OFF
1246 G/M/BA f< 1
Fail class F1…F7 Warning (F2)
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de frequência baixar e passar o tempo programado.
1250 G/M/BA Subfrequencia 2
1251 G/M/BA f< 2
Setpoint 80.0% 100.0%
93.0%
1252 G/M/BA f< 2
Timer 0.2 s 100.0 s
3.0 sec
1253 G/M/BA f< 2
Relay A
Not used
Option dep.
Not used
1254 G/M/BA f< 2
Relay B
Not used
Option dep.
Not used
1255 G/M/BA f< 2
Enable OFF ON
OFF
1256 G/M/BA f< 2
Fail class F1…F7 Warning (F2)
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de frequência baixar e passar o tempo programado.
1260 G/M/BA Subfrequencia 3
1261 G/M/BA f< 3
Setpoint 80.0% 100.0%
90.0%
1262 G/M/BA f< 3
Timer 0.2 s 100.0 s
1.0 sec
1263 G/M/BA f< 3
Relay A
Not used
Option dep.
Not used
1264 G/M/BA f< 3
Relay B
Not used
Option dep.
Not used
Opção A1/A2/A3/B1/ C1 Add-on
proteção
O alarme e a classe de falha são ativados quando o valor de frequência baixar e passar o tempo programado.
AGC-3 Alarm and Parameter List
DEIF A/S Page 18 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1265 G/M/BA f< 3
Enable OFF ON
OFF
1266 G/M/BA f< 3
Fail class F1…F7 Warning (F2)
Proteções de tensão no Barramento
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1270 Sobretensão Do Barramento 1
1271 BB U> 1 Setpoint
100.0% 120.0%
105.0%
1272 BB U> 1 Timer 0.0 s 99.9 s
0.5 s
1273 BB U> 1 Relay
A Not used Option dep.
Not used
1274 BB U> 1 Relay
B Not used Option dep.
Not used
1275 BB U> 1 Enable OFF ON
ON
1276 BB U> 1 Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de tensão passar o valor e o tempo programado.
1280 Sobretensão Do Barramento 2
1281 BB U> 2 Setpoint
100.0% 120.0%
120.0%
1282 BB U> 2 Timer 0.0 s 99.9 s
0.3 s
1283 BB U> 2 Relay
A Not used Option dep.
Not used
1284 BB U> 2 Relay
B Not used Option dep.
Not used
1285 BB U> 2 Enable OFF ON
ON
1286 BB U> 2 Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de tensão passar o valor e o tempo programado.
1290 Sobretensão Do Barramento 3
1291 BB U> 3 Setpoint
100.0% 120.0%
130.0%
1292 BB U> 3 Timer 0.0 s 99.9 s
0.1 s
1293 BB U> 3 Relay
A Not used Option dep.
Not used
Opção A1/A2/A3/B1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de tensão passar o valor e o tempo programado.
As proteções de tensão são baseadas nas configurações nominais.
AGC-3 Alarm and Parameter List
DEIF A/S Page 19 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1294 BB U> 3 Relay
B Not used Option dep.
Not used
1295 BB U> 3 Enable OFF ON
OFF
1296 BB U> 3 Fail class
F1…F7 Warning (F2)
1300 Subtensão Do Barramento 1
1301 BB U< 1 Setpoint
50.0% 100.0%
95.0%
1302 BB U< 1 Timer 0.0 s 99.9 s
0.5 s
1303 BB U< 1 Relay
A Not used Option dep.
Not used
1304 BB U< 1 Relay
B Not used Option dep.
Not used
1305 BB U< 1 Enable OFF ON
ON
1306 BB U< 1 Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de tensão baixar o valor e passar o tempo programado.
1310 Subtensão Do Barramento 2
1311 BB U< 2 Setpoint
50.0% 100.0%
80.0%
1312 BB U< 2 Timer 0.0 s 99.9 s
0.3 s
1313 BB U< 2 Relay
A Not used Option dep.
Not used
1314 BB U< 2 Relay
B Not used Option dep.
Not used
1315 BB U< 2 Enable OFF ON
ON
1316 BB U< 2 Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de tensão baixar o valor e passar o tempo programado.
1320 Subtensão Do Barramento 3
1321 BB U< 3 Setpoint
50.0% 100.0%
70.0%
1322 BB U< 3 Timer 0.0 s 99.9 s
0.20 s
1323 BB U< 3 Relay
A Not used Option dep.
Not used
1324 BB U< 3 Relay
B Not used Option dep.
Not used
1325 BB U< 3 Enable OFF ON
OFF
1326 BB U< 3 Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de tensão baixar o valor e passar o tempo programado.
AGC-3 Alarm and Parameter List
DEIF A/S Page 20 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1330 Subtensão Do Barramento 4
1331 BB U< 4 Setpoint
50.0% 100.0%
60.0%
1332 BB U< 4 Timer 0.0 s 99.9 s
0.1 s
1333 BB U< 4 Relay
A Not used Option dep.
Not used
1334 BB U< 4 Relay
B Not used Option dep.
Not used
1335 BB U< 4 Enable OFF ON
OFF
1336 BB U< 4 Fail class
F1…F7 Warning (F2)
Opção A1/A2/A3/B1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de tensão baixar o valor e passar o tempo programado.
1340 Tipos De Medição Do Barramento
1341 BB Voltage trip
Setpoint
Ph-Ph Ph-N
Opção A1/A2/A3/B1 Add-on proteção
Selecionar detecção de tensão entre fase-fase ou fase-neutro.
Proteção de frequência noBarramento
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1350 Sobrefrequencia Do Barramento 1
1351 BB f> 1 Setpoint 100.0% 120.0%
105.0%
1352 BB f> 1 Timer 0.0 sec 99.9 sec
0.50 sec
1353 BB f> 1 Relay A Not used Option dep.
Not used
1354 BB f> 1 Relay B Not used Option dep.
Not used
1355 BB f> 1 Enable OFF ON
ON
1356 BB f> 1 Fail class F1…F7 Warning (F2)
Opção A1/A2/A3/B
1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de frequência passar o valor e o tempo programado.
1360 Sobrefrequencia Do Barramento 2
1361 BB f> 2 Setpoint 100.0% 120.0%
110.0%
1362 BB f> 2 Timer 0.0 sec 99.9 sec
0.3 sec
Opção A1/A2/A3/B
1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de frequência passar o
As proteções de frequencia são baseadas nas configurações nominais.
AGC-3 Alarm and Parameter List
DEIF A/S Page 21 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1363 BB f> 2 Relay A Not used Option dep.
Not used
1364 BB f> 2 Relay B Not used Option dep.
Not used
1365 BB f> 2 Enable OFF ON
ON
1366 BB f> 2 Fail class F1…F7 Warning (F2)
valor e o tempo programado.
1370 Sobrefrequencia Do Barramento 3
1371 BB f> 3 Setpoint 100.0% 120.0%
120.0%
1372 BB f> 3 Timer 0.0 sec 99.9 sec
0.1 sec
1373 BB f> 3 Relay A Not used Option dep.
Not used
1374 BB f> 3 Relay B Not used Option dep.
Not used
1375 BB f> 3 Enable OFF ON
OFF
1376 BB f> 3 Fail class F1…F7 Warning (F2)
Opção A1/A2/A3/B
1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de frequência passar o valor e o tempo programado.
1380 Subfrequencia Do Barramento 1
1381 BB f< 1 Setpoint 80.0% 100.0%
96.0%
1382 BB f< 1 Timer 0.0 s 99.9 s
0.5 sec
1383 BB f< 1 Relay A Not used Option dep.
Not used
1384 BB f< 1 Relay B Not used Option dep.
Not used
1385 BB f< 1 Enable OFF ON
ON
1386 BB f< 1 Fail class F1…F7 Warning (F2)
Opção A1/A2/A3/B
1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de frequência baixar e passar o tempo programado.
1390 Subfrequencia Do Barramento 2
1391 BB f< 2 Setpoint 80.0% 100.0%
93.0%
1392 BB f< 2 Timer 0.0 sec 99.9 sec
1.0 sec
1393 BB f< 2 Relay A Not used Option dep.
Not used
1394 BB f< 2 Relay B Not used Option dep.
Not used
Opção A1/A2/A3/B
1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de frequência baixar e passar o tempo programado.
AGC-3 Alarm and Parameter List
DEIF A/S Page 22 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1395 BB f< 2 Enable OFF ON
ON
1396 BB f< 2 Fail class F1…F7 Warning (F2)
1400 Subfrequencia Do Barramento 3
1401 BB f< 3 Setpoint 80.0% 100.0%
92.0%
1402 BB f< 3 Timer 0.0 sec 99.9 sec
0.5 sec
1403 BB f< 3 Relay A Not used Option dep.
Not used
1404 BB f< 3 Relay B Not used Option dep.
Not used
1405 BB f< 3 Enable OFF ON
OFF
1406 BB f< 3 Fail class F1…F7 Warning (F2)
Opção A1/A2/A3/B
1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de frequência baixar e passar o tempo programado.
1410 Subfrequencia Do Barramento 4
1411 BB f< 4 Setpoint 80.0% 100.0%
90.0%
1412 BB f< 4 Timer 0. 0 sec 99.9 sec
0.1 sec
1413 BB f< 4 Relay A Not used Option dep.
Not used
1414 BB f< 4 Relay B Not used Option dep.
Not used
1415 BB f< 4 Enable OFF ON
OFF
1416 BB f< 4 Fail class F1…F7 Warning (F2)
Opção A1/A2/A3/B
1 Add-on proteção
O alarme e a classe de falha são ativados quando o valor de frequência baixar e passar o tempo programado.
Proteção de falha de rede
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1420 df/dt (ROCOF)
1421 Df/dt (ROCOF) Setpoint 1.5 Hz/s 10 Hz/s
1422 Df/dt (ROCOF) Timer 1 per 20 per
1423 Df/dt (ROCOF) Relay A R0
Option dep.
R0 (none)
Opção A1/A2
O alarme e a classe de falha serão ativados se a taxa df / dt for superior ao valor e o numero de periodos programado.
AGC-3 Alarm and Parameter List
DEIF A/S Page 23 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1424 Df/dt (ROCOF) Relay B R0
Option dep.
R0 (none)
1425 Df/dt (ROCOF) Enable OFF ON
OFF
1426 Df/dt (ROCOF) Fail class F1…F7 Trip MB (F4)
1430 Vector jump
1431 Vector jump Setpoint 1.0% 200.0%
110.0%
1432 Vector jump Relay A R0
Option dep.
R0 (none)
1433 Vector jump Relay B R0
Option dep.
R0 (none)
1434 Vector jump Enable OFF ON
OFF
1435 Vector jump Fail class F1…F7 Trip MB (F4)
Opção A1/A3
O alarme e a classe de falha são ativados quando o vector jump é detectado.
1440 Sequência Positiva De Baixa Tensão Do Barramento
1471 BB pos seq volt Setpoint 10.0% 110.0%
70.0%
1472 BB pos seq volt Timer 0.1 s 0.9 s
0.2 s
1473 BB pos seq volt Relay A R0
Option dep.
R0 (none)
1474 BB pos seq volt Relay B R0
Option dep.
R0 (none)
1475 BB pos seq volt Enable OFF ON
OFF
1476 BB pos seq volt Fail class F1…F7 Trip MB (F4)
Opção A4 O alarme e classe de falha são ativados quando simetricamente (sequencia positive) da tensão ficou abaixo do valor e passou o tempo programado.
Proteção de Sobrecarga.
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1450 G/M/BA Sobrecarga 1
1451 G/M/BA P> 1
Setpoint 1.0% 200.0%
95.0%
1452 G/M/BA P> 1
Timer 0.1 s 100.0 s
20.0 s
Opção C1 Add-on
proteção
O alarme e a classe de falha serão ativados quando a potência ficar acima do valor e do tempo
Configuração com relação a Potência Nominal
AGC-3 Alarm and Parameter List
DEIF A/S Page 24 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1453 G/M/BA P> 1 Relay A
R0 Option dep.
R0 (none)
1454 G/M/BA P> 1 Relay B
R0 Option dep.
R0 (none)
1455 G/M/BA P> 1
Enable OFF ON
OFF
1456 G/M/BA P> 1
Fail class F1…F7 Warning (F2)
programado.
1460 G/M/BA Sobrecarga 2
1461 G/M/BA P> 2
Setpoint 1.0% 200.0%
110.0%
1462 G/M/BA P> 2
Timer 0.1 s 100.0 s
10.0 s
1463 G/M/BA P> 2 Relay A
R0 Option dep.
R0 (none)
1464 G/M/BA P> 2 Relay B
R0 Option dep.
R0 (none)
1465 G/M/BA P> 2
Enable OFF ON
OFF
1466 G/M/BA P> 2
Fail class F1…F7 Warning (F2)
Opção C1 Add-on
proteção
O alarme e a classe de falha serão ativados quando a potência ficar acima do valor e do tempo programado.
1470 G/M/BA Sobrecarga 3
1471 G/M/BA P> 3
Setpoint 1.0% 200.0%
115.0%
1472 G/M/BA P> 3
Timer 0.1 s 100.0 s
5.0 s
1473 G/M/BA P> 3 Relay A
R0 Option dep.
R0 (none)
1474 G/M/BA P> 3 Relay B
R0 Option dep.
R0 (none)
1475 G/M/BA P> 3
Enable OFF ON
OFF
1476 G/M/BA P> 3
Fail class F1…F7 Warning (F2)
Opção C1 Add-on
proteção
O alarme e a classe de falha serão ativados quando a potência ficar acima do valor e do tempo programado.
1480 G/M/BA Sobrecarga 4
1481 G/M/BA P> 4
Setpoint 1.0% 200.0%
120.0%
1482 G/M/BA P> 4
Timer 0.1 s 100.0 s
3.0 s
1483 G/M/BA P> 4 Relay A
R0 Option dep.
R0 (none)
1484 G/M/BA P> 4 Relay B
R0 Option dep.
R0 (none)
Opção C1 Add-on
proteção
O alarme e a classe de falha serão ativados quando a potência ficar acima do valor e do tempo programado.
AGC-3 Alarm and Parameter List
DEIF A/S Page 25 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1485 G/M/BA P> 4
Enable OFF ON
OFF
1486 G/M/BA P> 4
Fail class F1…F7 Warning (F2)
1490 G/M/BA Sobrecarga 5
1491 G/M/BA P> 5
Setpoint 1.0% 200.0%
130.0%
1492 G/M/BA P> 5
Timer 0.1 s 100.0 s
1.0 s
1493 G/M/BA P> 5 Relay A
R0 Option dep.
R0 (none)
1494 G/M/BA P> 5 Relay B
R0 Option dep.
R0 (none)
1495 G/M/BA P> 5
Enable OFF ON
OFF
1496 G/M/BA P> 5
Fail class F1…F7 Warning (F2)
Opção C1 Add-on
proteção
O alarme e a classe de falha serão ativados quando a potência ficar acima do valor e do tempo programado.
Proteção contra desbalanceamento de Corrente
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1500 G/M/BA Desbalanceamento De Corrente
1501 G/M/BA Unbalance curr.
Setpoint 0.0% 100.0%
30.0%
1502 G/M/BA Unbalance curr.
Timer 0.1 s 100.0 s
10.0 s
1503 G/M/BA Unbalance curr. Relay A
R0 Option dep.
R0 (none)
1504 G/M/BA Unbalance curr. Relay B
R0 Option dep.
R0 (none)
1505 G/M/BA Unbalance curr.
Enable OFF ON
OFF
1506 G/M/BA Unbalance curr.
Fail class F1…F7 Trip GB (F3)
Opção C1 Add-on
proteção
Configuração relativa com a corrente nominal. O alarme e a classe de falha serão ativados na diferença entre a maxima leitura e a minima leitura quando a diferença de 3 medições de corrente passar o valor e o tempo programado.
Proteção contra desbalanceamento de tensão
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1510 G/M/BA Desbalanceamento De Tensão
1511 G/M/BA Unbalance volt.
Setpoint 0.0% 50.0%
10.0% Opção C1 Add-on
Configuração relativa com a tensão nominal.
AGC-3 Alarm and Parameter List
DEIF A/S Page 26 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1512 G/M/BA Unbalance volt.
Timer 0.1 s 100.0 s
10.0 s
1513 G/M/BA Unbalance volt. Relay A
R0 Option dep.
R0 (none)
1514 G/M/BA Unbalance volt. Relay B
R0 Option dep.
R0 (none)
1515 G/M/BA Unbalance volt.
Enable OFF ON
OFF
1516 G/M/BA Unbalance volt.
Fail class F1…F7 Trip GB (F3)
proteção O alarme e a classe de falha serão ativados na diferença entre a maxima leitura e a minima leitura quando a diferença de 3 medições de tensão passar o valor e o tempo programado.
Proteção contra importação de potência reativa (perda de excitação).
No. Setting
Min.
Max.
Factory setting
Notes Ref. Description
1520 G/M/BA Importação De Potência (perda de excitação)
1521 G/M/BA –Q> Setpoint 0.0% 150.0%
50.0%
1522 G/M/BA –Q> Timer 0.1 s 100.0 s
10.0 s
1523 G/M/BA –Q> Relay A R0
Option dep.
R0 (none)
1524 G/M/BA –Q> Relay B R0
Option dep.
R0 (none)
1525 G/M/BA –Q> Enable OFF ON
OFF
1526 G/M/BA –Q> Fail class F1…F7 Trip GB (F3)
Opção C1 Add-on
proteção
Configuração relativa com a potência nominal. O alarme e a classe de falha serão ativados quando ter importado Var maior do que o valor e o tempo programado.
Proteção contra exportação de potência reativa (sobre excitação).
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1530 G/M/BA Exportação De Potência Reativa (sobre excitação)
1531 G/M/BA Q> Setpoint 0.0% 100.0%
75.0%
1532 G/M/BA Q> Timer 0.1 s 100.0 s
10.0 s
1533 G/M/BA Q> Relay A R0
Option dep.
R0 (none)
1534 G/M/BA Q> Relay B R0
Option dep.
R0 (none)
1535 G/M/BA Q> Enable OFF ON
OFF
Opção C1 Add-on
proteção
Configuração relativa com a potência nominal. O alarme e a classe de falha serão ativados quando ter exportado Var maior do que o valor e o tempo programado. delay.
AGC-3 Alarm and Parameter List
DEIF A/S Page 27 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1536 G/M/BA Q> Fail class F1…F7 Trip GB (F3)
Sequencia negativa
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1540 G/M/BA Sequência Negativa De Corrente
1541 G/M/BA Neg seq I
Setpoint 1.0% 100.0%
20.0%
1542 G/M/BA Neg seq I
Timer 0.2 s 100.0 s
0.5 s
1543 G/M/BA Neg seq I
Relay A R0 Option dep.
R0 (none)
1544 G/M/BA Neg seq I
Relay B R0 Option dep.
R0 (none)
1545 G/M/BA Neg seq I
Enable OFF ON
OFF
1546 G/M/BA Neg seq I
Fail class
F1…F7 Trip MB (F4)
Opção C2 Configuração relativa com a corrente nominal. O alarme e a classe de falha serão ativados quando a sequencia negativa ter passado o valor e o tempo programado.
1550 G/M/BA Sequência Negativa De Tensão
1551 G/M/BA Neg seq U
Setpoint 1.0% 100.0%
5.0%
1552 G/M/BA Neg seq U
Timer 0.2 s 100.0 s
0.5 s
1553 G/M/BA Neg seq U
Relay A R0 Option dep.
R0 (none)
1554 G/M/BA Neg seq U
Relay B R0 Option dep.
R0 (none)
1555 G/M/BA Neg seq U
Enable OFF ON
OFF
1556 G/M/BA Neg seq U
Fail class
F1…F7 Trip MB (F4)
Opção C2 Configuração relativa com a tensão nominal. O alarme e a classe de falha serão ativados quando a sequencia negativa ter passado o valor e o tempo programado.
1560 G/M/BA Seleção De Sequência Negativa
1561 G/M/BA Neg seq select
Setpoint
G measurement
BB measurement
G measurement
Opção C2 Selecionar a sequencia negativa entre gerador ou barramento.
Sequência Zero
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1570 G/M/BA Sequência Zero De Corrente
1571 G/M/BA Zero seq I
Setpoint 0.0% 100.0%
20.0% Opção C2 Configuração relativa com a corrente
AGC-3 Alarm and Parameter List
DEIF A/S Page 28 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1572 G/M/BA Zero seq I
Timer 0.2 s 100.0 s
0.5 s
1573 G/M/BA Zero seq I
Relay A R0 Option dep.
R0 (none)
1574 G/M/BA Zero seq I
Relay B R0 Option dep.
R0 (none)
1575 G/M/BA Zero seq I
Enable OFF ON
OFF
1576 G/M/BA Zero seq I
Fail class
F1…F7 Trip MB (F4)
nominal. O alarme e a classe de falha serão ativados quando a sequencia zero ter passado o valor e o tempo programado.
1580 G/M/BA Sequência Zero De Tensão
1581 G/M/BA Zero seq U
Setpoint 1.0% 100.0%
5.0%
1582 G/M/BA Zero seq U
Timer 0.2 s 100.0 s
0.5 s
1583 G/M/BA Zero seq U
Relay A R0 Option dep.
R0 (none)
1584 G/M/BA Zero seq U
Relay B R0 Option dep.
R0 (none)
1585 G/M/BA Zero seq U
Enable OFF ON
OFF
1586 G/M/BA Zero seq U
Fail class
F1…F7 Trip MB (F4)
Opção C2 Configuração relativa com a tensão nominal. O alarme e a classe de falha serão ativados quando a sequencia zero ter passado o valor e o tempo programado.
1590 G/M/BA Seleção De Sequência Zero
1591 G/M/BA Zero seq select
Setpoint
G measurement
BB measurement
G measurement
Opção C2 Selecionar a sequencia zero entre gerador ou barramento.
Proteção contra sobrecorrente direcional
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1600 G/M/BA Sobrecorrente Direcional 1
1601 G/M/BA I> direct 1
Setpoint -200.0% 200.0%
120.0%
1602 G/M/BA I> direct 1
Timer 0.0 s 100.0 s
0.1 s
1603 G/M/BA I> direct 1 Relay A
R0 Option dep.
R0 (none)
1604 G/M/BA I> direct 1 Relay B
R0 Option dep.
R0 (none)
1605 G/M/BA I> direct 1
Enable OFF ON
OFF
1606 G/M/BA I> direct 1
Fail class F1…F7 Trip MB (F4)
Opção A5 Configuração relativa com a corrente nominal. O alarme e a classe de falha serão ativados quando a sobrecorrente direcional ter passado o valor e o tempo programado.
1610 G/M/BA Sobrecorrente Direcional 2
AGC-3 Alarm and Parameter List
DEIF A/S Page 29 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1611 G/M/BA I> direct 2
Setpoint -200.0% 200.0%
130.0%
1612 G/M/BA I> direct 2
Timer 0.0 s 100.0 s
0.1 s
1613 G/M/BA I> direct 2 Relay A
R0 Option dep.
R0 (none)
1614 G/M/BA I> direct 2 Relay B
R0 Option dep.
R0 (none)
1615 G/M/BA I> direct 2
Enable OFF ON
OFF
1616 G/M/BA I> direct 2
Fail class F1…F7 Trip MB (F4)
Opção A5 Configuração relativa com a corrente nominal. O alarme e a classe de falha serão ativados quando a sobrecorrente direcional ter passado o valor e o tempo programado.
Desbalanceamento de tensão do barramento.
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
1620 Desbalanceamento De Tensão No BB
1621 BB Unbalance U Setpoint 0.0% 50.0%
10.0%
1622 BB Unbalance U Timer 0.1 s 100.0 s
10.0 s
1623 BB Unbalance U Relay A R0
Option dep.
R0 (none)
1624 BB Unbalance U Relay B R0
Option dep.
R0 (none)
1625 BB Unbalance U Enable OFF ON
OFF
1626 BB Unbalance U Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Configuração relativa com a tensão nominal. O alarme e a classe de falha serão ativados na diferença entre a maxima leitura e a minima leitura quando a diferença de 3 medições de tensão do barramento passar o valor e o tempo programado.
Sincronização e alarmes dos disjuntores.
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2120 Janela De Sincronismo
2121 Sync window Setpoint 2.0% 20.0%
15%
2122 Sync window Timer 0.1 sec 2.0 sec
0.5 sec
2123 Sync window Output A Not used Option dep.
Not used
2124 Sync window Output B Not used Option dep.
Not used
Designers Reference Handbook
O alarme ativaria se a tensão atual sofresse uma variação com a tensão nominal nesta porcentagem.
AGC-3 Alarm and Parameter List
DEIF A/S Page 30 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2125 Sync window Enable OFF ON
OFF
2130 GB/TB/BTB Falha De Sincronização Dos Disjuntores
2131 GB/TB/BTB sync failure
Delay 3.0 sec 300.0 sec
60.0 sec
2132 GB/TB/BTB sync failure
Relay output A
Not used Option dep.
Not used
2133 GB/TB/BTB sync failure
Relay output B
Not used Option dep.
Not used
2134 GB/TB/BTB sync failure
Enable OFF ON
ON
2135 GB/TB/BTB sync failure
Fail class F1…F7 Warning (F2)
Designers Reference Handbook
GB: Disjuntor do Gerador TB: Disjuntor Tie breaker (Unidade do Mains) BTB: Disjuntor BUS tie. O controle não tiver sucesso ao tentar sincronizar o disjuntor ao barramento neste período de tempo.
2140 Falha De Sincronização Dos Disjuntores Da Rede
2141 MB sync failure Delay 3.0 sec 300.0 sec
60.0 sec
2142 MB sync failure Relay
output A
Not used Option dep.
Not used
2143 MB sync failure Relay
output B
Not used Option dep.
Not used
2144 MB sync failure Enable OFF ON
OFF
2145 MB sync failure Fail class F1…F7 Warning (F2)
Designers Reference Handbook
O controle não tiver sucesso ao tentar sincronizar o disjuntor ao barramento neste período de tempo.
2150 Erro De Sequência De Fase
2151 Phase seq error Relay
output A
Not used Option dep.
Not used
2152 Phase seq error Relay
output B
Not used Option dep.
Not used
2153 Phase seq error Fail class F1…F7 Block (F1)
Designers Reference Handbook
Durante o sincronismo o controle detecta a direção da rotação das fases do gerador e se estao na direção de oposição ao do barramento.
2160 GB/TB/BTB Falha De Abertura Dos Disjuntores
2161 GB/TB/BTB open fail
Delay 1.0 sec 5.0 sec
2.0 sec
2162 GB/TB/BTB open fail
Relay output A
Not used Option dep.
Not used
2163 GB/TB/BTB open fail
Relay output B
Not used Option dep.
Not used
2164 GB/TB/BTB open fail
Enable OFF ON
ON
2165 GB/TB/BTB open fail
Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se um sinal para abrir o disjuntor for enviado e o feedback não mudar a posição de ON para OFF ocorrerá um alarme em 2s.
2170 GB/TB/BTB Falha De Fechamento Dos Disjuntores
AGC-3 Alarm and Parameter List
DEIF A/S Page 31 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2171 GB/BTB/BTB close fail
Delay 1.0 sec 5.0 sec
2.0 sec
2172 GB/BTB/BTB close fail
Relay output A
Not used Option dep.
Not used
2173 GB/BTB/BTB close fail
Relay output B
Not used Option dep.
Not used
2174 GB/BTB/BTB close fail
Enable OFF ON
ON
2175 GB/BTB/BTB close fail
Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se um sinal para fechar o disjuntor for enviado e o feedback não mudar a posição de OFF para ON ocorrerá um alarme em 2s.
2180 GB/TB/BTB Falha De Posição Dos Disjuntores
2181 GB/TB/BTB pos fail
Delay 1.0 sec 5.0 sec
1.0 sec
2182 GB/TB/BTB pos fail
Relay output A
Not used Option dep.
Not used
2183 GB/TB/BTB pos fail
Relay output B
Not used Option dep.
Not used
2184 GB/TB/BTB pos fail
Enable OFF ON
ON
2185 GB/TB/BTB pos fail
Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Este alarme ocorreria se os feedbacks dos disjuntores estiverem perdidos ou ativos ao mesmo tempo por 2s.
2200 Falha De Abertura Do Disjuntor Da Rede
2201 MB open fail Delay 1.0 sec 5.0 sec
2.0 sec
2202 MB open fail Relay
output A
Not used Option dep.
Not used
2203 MB open fail Relay
output B
Not used Option dep.
Not used
2204 MB open fail Enable OFF ON
ON
2205 MB open fail Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se um sinal para abrir o disjuntor for enviado e o feedback não mudar a posição de ON para OFF ocorrerá um alarme em 2s.
2210 Falha De Fechamendo Do Disjuntor Da Rede
2211 MB close fail Delay 1.0 sec 5.0 sec
2.0 sec
2212 MB close fail Relay
output A
Not used Option dep.
Not used
2213 MB close fail Relay
output B
Not used Option dep.
Not used
2214 MB close fail Enable OFF ON
ON
2215 MB close fail Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se um sinal para fechar o disjuntor for enviado e o feedback não mudar a posição de OFF para ON ocorrerá um alarme em 2s.
2220 Falha De Posição Do Disjuntor Da Rede
AGC-3 Alarm and Parameter List
DEIF A/S Page 32 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2221 MB pos fail Delay 1.0 sec 5.0 sec
1.0 sec
2222 MB pos fail Relay
output A
Not used Option dep.
Not used
2223 MB pos fail Relay
output B
Not used Option dep.
Not used
2224 MB pos fail Enable OFF ON
ON
2225 MB pos fail Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Este alarme ocorreria se os feedbacks dos disjuntores estiverem perdidos ou ativos ao mesmo tempo por 2s.
2270 Falha Do Close before excitation
2271 Cl.bef.exc.fail Delay 0.0 sec 999.0 sec
5.0 sec
2272 Cl.bef.exc.fail Relay
output A
Not used Option dep.
Not used
2273 Cl.bef.exc.fail Relay
output B
Not used Option dep.
Not used
2274 Cl.bef.exc.fail Enable OFF ON
ON
2275 Cl.bef.exc.fail Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Este alarme ocorreria se o feedback do disjuntor não estiver ON depois de 2s do commando de fechamento.
AGC-3 Alarm and Parameter List
DEIF A/S Page 33 of 112
Alarmes dos reguladores
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2560 Falha Do Regulador De Velocidade
2561 Gov. reg fail Deadband 1.0% 100.0%
30.0%
2562 Gov. reg fail Delay 10.0 sec 300.0 sec
60.0 sec
2563 Gov. reg fail Relay
output A
Not used Option
dependent Not used
2564 Gov. reg fail Relay
output B
Not used Option
dependent Not used
Designers Reference Handbook
O alarme sera ativado, se a diferença entre o valor medido e o set point estiver fora da zona morta por um longo período especificado no set point.
2630 Erro ao Tirar a carga
2631 Deload error Delay 0.0 s 60.0 s
10.0 s
2632 Deload error Relay output A
Not used Option
dependent Not used
2633 Deload error Relay output B
Not used Option
dependent Not used
2634 Deload error Enable OFF ON
ON
2635 Deload error Fail class F1…F7 Warning (F2)
Designers Reference Handbook
O alarme sera ativado se ocorrer uma falha no gerador ao devolver a carga no tempo programado.
2680 Falha No Regulador De Tensão
2681 AVR reg. failure Deadband 1.0% 100.0%
30.0%
2682 AVR reg. failure Delay 10.0 s 300.0 s
60.0 s
1153 AVR reg. failure Relay A R0
Option dep.
R0 (none)
1154 AVR reg. failure Relay B R0
Option dep.
R0 (none)
1155 AVR reg. failure Fail class F1…F7 Warning (F2)
Opção: controle
VAR (D1)
O alarme sera ativado, se a diferença entre o valor medido e o set point estiver fora da zona morta por um longo período especificado no set point.
AGC-3 Alarm and Parameter List
DEIF A/S Page 34 of 112
Programar Entrada Digital 23-27
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
3000 Entrada Digital 23
3001 Dig. input 23 Delay 0.0 sec 100.0 sec
10.0 sec
3002 Dig. input 23 Relay output A
Not used Option dep.
Not used
3003 Dig. input 23 Relay output B
Not used Option dep.
Not used
3004 Dig. input 23 Enable OFF ON
OFF
3005 Dig. input 23 Fail class F1…F7 Warning (F2)
3006 Dig. input 23 N/X N/O N/C
N/O
Designers Reference Handbook
A entrada digital é configurável e pode ter diferente funções em diferente unidades.
Programar Entrada Digital 43-55
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
3130 Entrada Digital 43
3131 Dig. input 43 Delay 0.0 sec 100.0 sec
10.0 sec
3132 Dig. input 43 Relay output A
Not used Option dep.
Not used
3133 Dig. input 43 Relay output B
Not used Option dep.
Not used
3134 Dig. input 43 Enable OFF ON
OFF
3135 Dig. input 43 Fail class F1…F7 Warning (F2)
3136 Dig. input 43 N/X N/O N/C
N/O
Opção M12 A entrada digital é configurável e pode ter diferente funções em diferente unidades.
Algumas configurações aplicam para as entradas 24-27, configuráveis do 3010 ao 3040.
Algumas configurações aplicam para as entradas 44-55, configuráveis do 3140 ao 3250.
AGC-3 Alarm and Parameter List
DEIF A/S Page 35 of 112
Programar Entrada Digital 91-97
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
3330 Entrada Digital 91
3331 Dig. input 91 Delay 0.0 s 100.0 s
10.0 s
3332 Dig. input 91 Relay output A
R0 Option dep.
R0 (none)
3333 Dig. input 91 Relay output B
R0 Option dep.
R0 (none)
3334 Dig. input 91 Enable OFF ON
OFF
3335 Dig. input 91 Fail class F1…F7 Warning (F2)
3336 Dig. input 91 N/O - N/C N/O N/C
N/O
Opção: 7 entradas binárias no
slot #6 (M13.6)
A entrada digital é configurável e pode ter diferente funções em diferente unidades.
Programar Entrada Digital 102-108
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
3400 Entrada Digital 102
3401 Wire fail 102 Enable OFF ON
OFF
3402 Dig. input 102 Delay 0.0 sec 100.0 sec
10.0 sec
3403 Dig. input 102 Relay output A
Not used Option dep.
Not used
3404 Dig. input 102 Relay output B
Not used Option dep.
Not used
3405 Dig. input 102 Enable OFF ON
OFF
3406 Dig. input 102 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A entrada digital é configurável e pode ter diferente funções em diferente unidades. (Apenas se a multi-entrada 102 estiver configurada como entrada digital’).
3410 Entrada Digital 105
3411 Wire fail 105 Enable OFF ON
OFF
3412 Dig. input 105 Delay 0.0 sec 100.0 sec
10.0 sec
3413 Dig. input 105 Relay output A
Not used Option dep.
Not used
3414 Dig. input 105 Relay output B
Not used Option dep.
Not used
3415 Dig. input 105 Enable OFF ON
OFF
Designers Reference Handbook
A entrada digital é configurável e pode ter diferente funções em diferente unidades. (Apenas se a multi-entrada 105 estiver configurada como entrada digital’).
Algumas configurações aplicam para as entradas 92-97, configuráveis do 3340 ao 3390
AGC-3 Alarm and Parameter List
DEIF A/S Page 36 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
3416 Dig. input 105 Fail class F1…F7 Warning (F2)
3420 Entrada Digital 108
3421 Wire fail 108 Enable OFF ON
OFF
3422 Dig. input 108 Delay 0.0 sec 100.0 sec
10.0 sec
3423 Dig. input 108 Relay output A
Not used Option dep.
Not used
3424 Dig. input 108 Relay output B
Not used Option dep.
Not used
3425 Dig. input 108 Enable OFF ON
OFF
3426 Dig. input 108 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A entrada digital é configurável e pode ter diferente funções em diferente unidades. (Apenas se a multi-entrada 108 estiver configurada como entrada digital’).
Digital input 112-117 setup
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
3430 Entrada Digital 112
3431 Dig. input 112 Delay 0.0 sec 100.0 sec
10.0 sec
3432 Dig. input 112 Relay output A
Not used Option dep.
Not used
3433 Dig. input 112 Relay output B
Not used Option dep.
Not used
3434 Dig. input 112 Enable OFF ON
OFF
3435 Dig. input 112 Fail class F1…F7 Warning (F2)
3436 Dig. input 112 N/X N/O N/C
N/O
Designers Reference Handbook
A entrada digital é configurável e pode ter diferente funções em diferentes unidades.
Algumas configurações aplicam para as entradas 113-117, configuráveis do 3440 ao 3480.
AGC-3 Alarm and Parameter List
DEIF A/S Page 37 of 112
Parada de Emergencia
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
3490 Parada De Emergencia
3491 Emer. stop Delay 0.0 sec 100.0 sec
0.0 sec
3492 Emer. Stop Relay
output A
Not used Option
dependent Not used
3493 Emer. Stop Relay
output B
Not used Option
dependent Not used
3494 Emer. Stop Enable OFF ON
OFF
3495 Emer. stop Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A entrada da parade de Emergencia é destinada para um contato normalmente fechado.
Programar Entrada Digital 127-133
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
3500 Entrada Digital 127
3501 Dig. input 127 Delay 0.0 s 100.0 s
10.0 s
3502 Dig. input 127 Relay output A
R0 Option dep.
R0 (none)
3503 Dig. input 127 Relay output B
R0 Option dep.
R0 (none)
3504 Dig. input 127 Enable OFF ON
OFF
3505 Dig. input 127 Fail class F1…F7 Warning (F2)
3506 Dig. input 127 N/X N/O N/C
N/O
Opção: 7 entradas binárias no
slot #8 (M13.8)
A entrada digital é configurável e pode ter diferente funções em diferentes unidades.
Algumas configurações aplicam para as entradas 128-133, configuráveis do 3510 ao 3560.
AGC-3 Alarm and Parameter List
DEIF A/S Page 38 of 112
Programar Entrada Analógica (opção M15.6)
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4000 4-20 mA 91.1
4001 4-20 mA 91.1 Setpoint 4 mA 20 mA
10 mA
4002 4-20 mA 91.1 Delay 0.0 s 600.0 s
120.0 s
4003 4-20 mA 91.1 Relay A R0 Option dep.
R0 (none)
4004 4-20 mA 91.1 Relay B R0 Option dep.
R0 (none)
4005 4-20 mA 91.1 Enable OFF ON
OFF
4006 4-20 mA 91.1 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA
(M15.6)
Entrada analogical configurável.
4010 4-20 mA 91.2
4011 4-20 mA 91.2 Setpoint 4 mA 20 mA
10 mA
4012 4-20 mA 91.2 Delay 0.0 s 600.0 s
120.0 s
4013 4-20 mA 91.2 Relay A R0 Option dep.
R0 (none)
4014 4-20 mA 91.2 Relay B R0 Option dep.
R0 (none)
4015 4-20 mA 91.2 Enable OFF ON
OFF
4016 4-20 mA 91.2 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA (M15.6)
Entrada analogical configurável.
4020 Wire fail 4-20 mA 91
4021 W. fail ana 91 Relay A R0 Option dep.
R0 (none)
4022 W. fail ana 91 Relay B R0 Option dep.
R0 (none)
4023 W. fail ana 91 Enable OFF ON
OFF
4024 W. fail ana 91 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA (M15.6)
A falha de fio desconectado ocorreria caso a corrente de controle fica abaixo de 2mA ou exceda 22 mA. Nos dois casos o alarme seria ativado.
4030 4-20 mA 93.1
4031 4-20 mA 93.1 Setpoint 4 mA 20 mA
10 mA
4032 4-20 mA 93.1 Delay 0.0 s 600.0 s
120.0 s
4033 4-20 mA 93.1 Relay A R0 Option dep.
R0 (none)
4034 4-20 mA 93.1 Relay B R0 Option dep.
R0 (none)
4035 4-20 mA 93.1 Enable OFF ON
OFF
Opção: 4
entradas x 4-20 mA
(M15.6)
Entrada analogica configurável.
AGC-3 Alarm and Parameter List
DEIF A/S Page 39 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4036 4-20 mA 93.1 Fail class F1…F7 Warning (F2)
4040 4-20 mA 93.2
4041 4-20 mA 93.2 Setpoint 4 mA 20 mA
10 mA
4042 4-20 mA 93.2 Delay 0.0 s 600.0 s
120.0 s
4043 4-20 mA 93.2 Relay A R0 Option dep.
R0 (none)
4044 4-20 mA 93.2 Relay B R0 Option dep.
R0 (none)
4045 4-20 mA 93.2 Enable OFF ON
OFF
4046 4-20 mA 93.2 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA
(M15.6)
Entrada analogica configurável.
4050 Wire fail 4-20 mA 93
4051 W. fail ana 93 Relay A R0 Option dep.
R0 (none)
4052 W. fail ana 93 Relay B R0 Option dep.
R0 (none)
4053 W. fail ana 93 Enable OFF ON
OFF
4054 W. fail ana 93 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA
(M15.6)
A falha de fio desconectado ocorreria caso a corrente de controle fica abaixo de 2mA ou exceda 22 mA. Nos dois casos o alarme seria ativado.
4060 4-20 mA 95.1
4061 4-20 mA 95.1 Setpoint 4 mA 20 mA
10 mA
4062 4-20 mA 95.1 Delay 0.0 s 600.0 s
120.0 s
4063 4-20 mA 95.1 Relay A R0 Option dep.
R0 (none)
4064 4-20 mA 95.1 Relay B R0 Option dep.
R0 (none)
4065 4-20 mA 95.1 Enable OFF ON
OFF
4066 4-20 mA 95.1 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA
(M15.6)
Entrada analogica configurável.
4070 4-20 mA 95.2
4071 4-20 mA 95.2 Setpoint 4 mA 20 mA
10 mA
4072 4-20 mA 95.2 Delay 0.0 s 600.0 s
120.0 s
4073 4-20 mA 95.2 Relay A R0 Option dep.
R0 (none)
4074 4-20 mA 95.2 Relay B R0 Option dep.
R0 (none)
4075 4-20 mA 95.2 Enable OFF ON
OFF
4076 4-20 mA 95.2 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA
(M15.6)
Entrada analogical configurável.
AGC-3 Alarm and Parameter List
DEIF A/S Page 40 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4080 Wire fail 4-20 mA 95
4081 W. fail ana 95 Relay A R0 Option dep.
R0 (none)
4082 W. fail ana 95 Relay B R0 Option dep.
R0 (none)
4083 W. fail ana 95 Enable OFF ON
OFF
4084 W. fail ana 95 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA
(M15.6)
A falha de fio desconectado ocorreria caso a corrente de controle fica abaixo de 2mA ou exceda 22 mA. Nos dois casos o alarme seria ativado.
4090 4-20 mA 97.1
4091 4-20 mA 97.1 Setpoint 4 mA 20 mA
10 mA
4092 4-20 mA 97.1 Delay 0.0 s 600.0 s
120.0 s
4093 4-20 mA 97.1 Relay A R0 Option dep.
R0 (none)
4094 4-20 mA 97.1 Relay B R0 Option dep.
R0 (none)
4095 4-20 mA 97.1 Enable OFF ON
OFF
4096 4-20 mA 97.1 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA
(M15.6)
Entrada analogica configurável.
4100 4-20 mA 97.2
4101 4-20 mA 97.2 Setpoint 4 mA 20 mA
10 mA
4102 4-20 mA 97.2 Delay 0.0 s 600.0 s
120.0 s
4103 4-20 mA 97.2 Relay A R0 Option dep.
R0 (none)
4104 4-20 mA 97.2 Relay B R0 Option dep.
R0 (none)
4105 4-20 mA 97.2 Enable OFF ON
OFF
4106 4-20 mA 97.2 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA
(M15.6)
Entrada analogica configurável.
4110 Wire fail 4-20 mA 97
4111 W. fail ana 97 Relay A R0 Option dep.
R0 (none)
4112 W. fail ana 97 Relay B R0 Option dep.
R0 (none)
4113 W. fail ana 97 Enable OFF ON
OFF
4114 W. fail ana 97 Fail class F1…F7 Warning (F2)
Opção: 4
entradas x 4-20 mA
(M15.6)
A falha de fio desconectado ocorreria caso a corrente de controle fica abaixo de 2mA ou exceda 22 mA. Nos dois casos o alarme seria ativado.
AGC-3 Alarm and Parameter List
DEIF A/S Page 41 of 112
Programar Entrada Analógica Multi-functional
Multi-input no. 102
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4120 4-20 mA 102.1
4121 4-20 mA 102.1 Setpoint 4 mA 20 mA
10 mA
4122 4-20 mA 102.1 Delay 0.0 sec 999.0 sec
120.0 sec
4123 4-20 mA 102.1 Relay output A
Not used Option dep.
Not used
4124 4-20 mA 102.1 Relay output B
Not used Option dep.
Not used
4125 4-20 mA 102.1 Enable OFF ON
OFF
4126 4-20 mA 102.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como 4-20mA.
4130 4-20 mA 102.2
4131 4-20 mA 102.2 Setpoint 4 mA 20 mA
10 mA
4132 4-20 mA 102.2 Delay 0.0 sec 999.0 sec
120.0 sec
4133 4-20 mA 102.2 Relay output A
Not used Option dep.
Not used
4134 4-20 mA 102.2 Relay output B
Not used Option dep.
Not used
4135 4-20 mA 102.2 Enable OFF ON
OFF
4136 4-20 mA 102.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como 4-20mA.
4140 V DC 102.1
4141 V DC 102.1 Setpoint 0.0 V DC 40.0 V DC
20.0 V DC
4142 V DC 102.1 Delay 0.0 sec 999.0 sec
10.0 sec
4143 V DC 102.1 Relay output A
Not used Option dep.
Not used
4144 V DC 102.1 Relay output B
Not used Option dep.
Not used
4145 V DC 102.1 Enable OFF ON
OFF
4146 V DC 102.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como VDC.
4150 V DC 102.2
4151 V DC 102.2 Setpoint 0.0 V DC 40.0 V DC
20.0 V DC
Designers Reference
Uma multi-entrada 102 pode ser configurada
Os menus disponíveis para multi-entrada 102 dependem do tipo de entrada configurados no PC utility software (menu 10980).
AGC-3 Alarm and Parameter List
DEIF A/S Page 42 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4152 V DC 102.2 Delay 0.0 sec 999.0 sec
10.0 sec
4153 V DC 102.2 Relay output A
Not used Option dep.
Not used
4154 V DC 102.2 Relay output B
Not used Option dep.
Not used
4155 V DC 102.2 Enable OFF ON
OFF
4156 V DC 102.2 Fail class F1…F7 Warning (F2)
Handbook como VDC.
4160 Pt100 102.1
4161 PT 102.1 Setpoint -49 482
80
4162 PT 102.1 Delay 0.0 sec 999.0 sec
5.0 sec
4163 PT 102.1 Relay output A
Not used Option dep.
Not used
4164 PT 102.1 Relay output B
Not used Option dep.
Not used
4165 PT 102.1 Enable OFF ON
OFF
4166 PT 102.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como Pt100. Pt100. O setpoint do Pt100 pode ser em deg. C ou Fahrenheit, dependendo da unidade de seleção (parâmetro 10970).
4170 Pt100 102.2
4171 PT 102.2 Setpoint -49 482
80
4172 PT 102.2 Delay 0.0 sec 999.0 sec
5.0 sec
4173 PT 102.2 Relay output A
Not used Option dep.
Not used
4174 PT 102.2 Relay output B
Not used Option dep.
Not used
4175 PT 102.2 Enable OFF ON
OFF
4176 PT 102.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como Pt100. Pt100. O setpoint do Pt100 pode ser em deg. C ou Fahrenheit, dependendo da unidade de seleção (parâmetro 10970).
4180 VDO oil 102.1
4181 VDO oil 102.1 Setpoint 0.0 145.0
4.0
4182 VDO oil 102.1 Delay 0.0 sec 999.0 sec
5.0 sec
4183 VDO oil 102.1 Relay output A
Not used Option dep.
Not used
4184 VDO oil 102.1 Relay output B
Not used Option dep.
Not used
4185 VDO oil 102.1 Enable OFF ON
OFF
4186 VDO oil 102.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como VDO pressao do oleo. O setpoint de pressão do oleo pode ser em Bar ou PSI, dependendo da unidade de seleção (parâmetro 10970).
4190 VDO oil 102.2
AGC-3 Alarm and Parameter List
DEIF A/S Page 43 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4191 VDO oil 102.2 Setpoint 0.0 145.0
5.0
4192 VDO oil 102.2 Delay 0.0 sec 999.0 sec
5.0 sec
4193 VDO oil 102.2 Relay output A
Not used Option dep.
Not used
4194 VDO oil 102.2 Relay output B
Not used Option dep.
Not used
4195 VDO oil 102.2 Enable OFF ON
OFF
4196 VDO oil 102.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como VDO pressao do oleo. O setpoint de pressão do oleo pode ser em Bar ou PSI, dependendo da unidade de seleção (parâmetro 10970).
4200 VDO water 102.1
4201 VDO water 102.1 Setpoint -49 482
100
4202 VDO water 102.1 Delay 0.0 sec 999.0 sec
5.0 sec
4203 VDO water 102.1 Relay output A
Not used Option dep.
Not used
4204 VDO water 102.1 Relay output B
Not used Option dep.
Not used
4205 VDO water 102.1 Enable OFF ON
OFF
4206 VDO water 102.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como VDO temperatura da água. O setpoint de temperatura da água pode ser em C ou F, dependendo da unidade de seleção (parâmetro 10970).
4210 VDO water 102.2
4211 VDO water 102.2 Setpoint -49 482
110
4212 VDO water 102.2 Delay 0.0 sec 999.0 sec
5.0 sec
4213 VDO water 102.2 Relay output A
Not used Option dep.
Not used
4214 VDO water 102.2 Relay output B
Not used Option dep.
Not used
4215 VDO water 102.2 Enable OFF ON
OFF
4216 VDO water 102.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como VDO temperatura da água. O setpoint de temperatura da água pode ser em C ou F, dependendo da unidade de seleção (parâmetro 10970).
4220 VDO fuel level 102.1
4221 VDO fuel 102.1 Setpoint 0% 100%
10%
4222 VDO fuel 102.1 Delay 0.0 sec 999.0 sec
10.0 sec
4223 VDO fuel 102.1 Relay output A
Not used Option dep.
Not used
4224 VDO fuel 102.1 Relay output B
Not used Option dep.
Not used
4225 VDO fuel 102.1 Enable OFF ON
OFF
4226 VDO fuel 102.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como VDO de nível de combustível
AGC-3 Alarm and Parameter List
DEIF A/S Page 44 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4230 VDO fuel level 102.2
4231 VDO fuel 102.2 Setpoint 0% 100%
10%
4232 VDO fuel 102.2 Delay 0.0 sec 999.0 sec
10.0 sec
4233 VDO fuel 102.2 Relay output A
Not used Option dep.
Not used
4234 VDO fuel 102.2 Relay output B
Not used Option dep.
Not used
4235 VDO fuel 102.2 Enable OFF ON
OFF
4236 VDO fuel 102.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 102 pode ser configurada como VDO de nível de combustível
4240 Wire fail 102
4241 W. fail 102 Relay output A
Not used Option dep.
Not used
4242 W. fail 102 Relay output B
Not used Option dep.
Not used
4243 W. fail 102 Enable OFF ON
OFF
4244 W. fail 102 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A falha do fio desconectado é detectado e ativada.
Multi-input no. 105
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4250 4-20 mA 105.1
4251 4-20 mA 105.1 Setpoint 4 mA 20 mA
10 mA
4252 4-20 mA 105.1 Delay 0.0 sec 999.0 sec
120.0 sec
4253 4-20 mA 105.1 Relay output A
Not used Option dep.
Not used
4254 4-20 mA 105.1 Relay output B
Not used Option dep.
Not used
4255 4-20 mA 105.1 Enable OFF ON
OFF
4256 4-20 mA 105.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como 4-20mA.
4260 4-20 mA 105.2
4261 4-20 mA 105.2 Setpoint 4 mA 20 mA
10 mA Designers Reference
Uma multi-entrada 105 pode ser configurada
Os menus disponíveis para multi-entrada 102 dependem do tipo de entrada configurados no PC utility software (menu 10990).
AGC-3 Alarm and Parameter List
DEIF A/S Page 45 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4262 4-20 mA 105.2 Delay 0.0 sec 999.0 sec
120.0 sec
4263 4-20 mA 105.2 Relay output A
Not used Option dep.
Not used
4264 4-20 mA 105.2 Relay output B
Not used Option dep.
Not used
4265 4-20 mA 105.2 Enable OFF ON
OFF
4266 4-20 mA 105.2 Fail class F1…F7 Warning (F2)
Handbook como 4-20mA.
4270 V DC 105.1
4271 V DC 105.1 Setpoint 0.0 V DC 40.0 V DC
20.0 V DC
4272 V DC 105.1 Delay 0.0 sec 999.0 sec
10.0 sec
4273 V DC 105.1 Relay output A
Not used Option dep.
Not used
4274 V DC 105.1 Relay output B
Not used Option dep.
Not used
4275 V DC 105.1 Enable OFF ON
OFF
4276 V DC 105.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como VDC.
4280 V DC 105.2
4281 V DC 105.2 Setpoint 0.0 V DC 40.0 V DC
20.0 V DC
4282 V DC 105.2 Delay 0.0 sec 999.0 sec
10.0 sec
4283 V DC 105.2 Relay output A
Not used Option dep.
Not used
4284 V DC 105.2 Relay output B
Not used Option dep.
Not used
4285 V DC 105.2 Enable OFF ON
OFF
4286 V DC 105.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como VDC.
4290 Pt100 105.1
4291 PT 105.1 Setpoint -49 482
80
4292 PT 105.1 Delay 0.0 sec 999.0 sec
5.0 sec
4293 PT 105.1 Relay output A
Not used Option dep.
Not used
4294 PT 105.1 Relay output B
Not used Option dep.
Not used
4295 PT 105.1 Enable OFF ON
OFF
4296 PT 105.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como Pt100. Pt100. O setpoint do Pt100 pode ser em deg. C ou Fahrenheit, dependendo da unidade de seleção (parâmetro 10970).
4300 Pt100 105.2
AGC-3 Alarm and Parameter List
DEIF A/S Page 46 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4301 PT 105.2 Setpoint -49 482
80
4302 PT 105.2 Delay 0.0 sec 999.0 sec
5.0 sec
4303 PT 105.2 Relay output A
Not used Option dep.
Not used
4304 PT 105.2 Relay output B
Not used Option dep.
Not used
4305 PT 105.2 Enable OFF ON
OFF
4306 PT 105.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como Pt100. Pt100. O setpoint do Pt100 pode ser em deg. C ou Fahrenheit, dependendo da unidade de seleção (parâmetro 10970).
4310 VDO oil 105.1
4311 VDO oil 105.1 Setpoint 0.0 145.0
4.0
4312 VDO oil 105.1 Delay 0.0 sec 999.0 sec
5.0 sec
4313 VDO oil 105.1 Relay output A
Not used Option dep.
Not used
4314 VDO oil 105.1 Relay output B
Not used Option dep.
Not used
4315 VDO oil 105.1 Enable OFF ON
OFF
4316 VDO oil 105.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como VDO pressao do oleo. O setpoint de pressão do oleo pode ser em Bar ou PSI, dependendo da unidade de seleção (parâmetro 10970).
4320 VDO oil 105.2
4321 VDO oil 105.2 Setpoint 0.0 145.0
5.0
4322 VDO oil 105.2 Delay 0.0 sec 999.0 sec
5.0 sec
4323 VDO oil 105.2 Relay output A
Not used Option dep.
Not used
4324 VDO oil 105.2 Relay output B
Not used Option dep.
Not used
4325 VDO oil 105.2 Enable OFF ON
OFF
4326 VDO oil 105.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como VDO pressao do oleo. O setpoint de pressão do oleo pode ser em Bar ou PSI, dependendo da unidade de seleção (parâmetro 10970).
4330 VDO water 105.1
4331 VDO water 105.1
Setpoint -49 482
100
4332 VDO water 105.1
Delay 0.0 sec 999.0 sec
5.0 sec
4333 VDO water 105.1
Relay output A
Not used Option dep.
Not used
4334 VDO water 105.1
Relay output B
Not used Option dep.
Not used
4335 VDO water 105.1
Enable OFF ON
OFF
4336 VDO water 105.1
Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como VDO temperatura da água. O setpoint de temperatura da água pode ser em C ou F, dependendo da unidade de seleção (parâmetro 10970).
AGC-3 Alarm and Parameter List
DEIF A/S Page 47 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4340 VDO water 105.2
4341 VDO water 105.2
Setpoint -49 482
110
4342 VDO water 105.2
Delay 0.0 sec 999.0 sec
5.0 sec
4343 VDO water 105.2
Relay output A
Not used Option dep.
Not used
4344 VDO water 105.2
Relay output B
Not used Option dep.
Not used
4345 VDO water 105.2
Enable OFF ON
OFF
4346 VDO water 105.2
Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como VDO temperatura da água. O setpoint de temperatura da água pode ser em C ou F, dependendo da unidade de seleção (parâmetro 10970).
4350 VDO fuel level 105.1
4351 VDO fuel 105.1 Setpoint 0% 100%
10%
4352 VDO fuel 105.1 Delay 0.0 sec 999.0 sec
10.0 sec
4353 VDO fuel 105.1 Relay output
A
Not used Option
dependent Not used
4354 VDO fuel 105.1 Relay output B
Not used Option dep.
Not used
4535 VDO fuel 105.1 Enable OFF ON
OFF
4356 VDO fuel 105.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como VDO de nível de combustível.
4360 VDO fuel level 105.2
4361 VDO fuel 105.2 Setpoint 0% 100%
10%
4362 VDO fuel 105.2 Delay 0.0 sec 999.0 sec
10.0 sec
4363 VDO fuel 105.2 Relay output A
Not used Option dep.
Not used
4364 VDO fuel 105.2 Relay output B
Not used Option dep.
Not used
4365 VDO fuel 105.2 Enable OFF ON
OFF
4366 VDO fuel 105.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 105 pode ser configurada como VDO de nível de combustível.
4370 Wire fail 105
4371 W. fail 105 Relay output
A
Not used Option
dependent Not used
4372 W. fail 105 Relay output B
Not used Option dep.
Not used
4373 W. fail 105 Enable OFF ON
OFF
4374 W. fail 105 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A falha do fio desconectado é detectado e ativada.
AGC-3 Alarm and Parameter List
DEIF A/S Page 48 of 112
Multi-input no. 108
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4380 4-20 mA 108.1
4381 4-20 mA 108.1 Setpoint 4 mA 20 mA
10 mA
4382 4-20 mA 108.1 Delay 0.0 sec 999.0 sec
120.0 sec
4383 4-20 mA 108.1 Relay output A
Not used Option dep.
Not used
4384 4-20 mA 108.1 Relay output B
Not used Option dep.
Not used
4385 4-20 mA 108.1 Enable OFF ON
OFF
4386 4-20 mA 108.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como 4-20mA.
4390 4-20 mA 108.2
4391 4-20 mA 108.2 Setpoint 4 mA 20 mA
10 mA
4392 4-20 mA 108.2 Delay 0.0 sec 999.0 sec
120.0 sec
4393 4-20 mA 108.2 Relay output A
Not used Option dep.
Not used
4394 4-20 mA 108.2 Relay output B
Not used Option dep.
Not used
4395 4-20 mA 108.2 Enable OFF ON
OFF
4396 4-20 mA 108.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como 4-20mA.
4400 V DC 108.1
4401 V DC 108.1 Setpoint 0.0 V DC 40.0 V DC
20.0 V DC
4402 V DC 108.1 Delay 0.0 sec 999.0 sec
10.0 sec
4403 V DC 108.1 Relay output A
Not used Option dep.
Not used
4404 V DC 108.1 Relay output B
Not used Option dep.
Not used
4405 V DC 108.1 Enable OFF ON
OFF
4406 V DC 108.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como VDC.
4410 V DC 108.2
4411 V DC 108.2 Setpoint 0.0 V DC 40.0 V DC
20.0 V DC
4412 V DC 108.2 Delay 0.0 sec 999.0 sec
10.0 sec
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como VDC.
Os menus disponíveis para multi-entrada 102 dependem do tipo de entrada configurados no PC utility software (menu 11000).
AGC-3 Alarm and Parameter List
DEIF A/S Page 49 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4413 V DC 108.2 Relay output A
Not used Option dep.
Not used
4414 V DC 108.2 Relay output B
Not used Option dep.
Not used
4415 V DC 108.2 Enable OFF ON
OFF
4416 V DC 108.2 Fail class F1…F7 Warning (F2)
4420 Pt100 108.1
4421 PT 108.1 Setpoint -49 482
80
4422 PT 108.1 Delay 0.0 sec 999.0 sec
5.0 sec
4423 PT 108.1 Relay output A
Not used Option dep.
Not used
4424 PT 108.1 Relay output B
Not used Option dep.
Not used
4425 PT 108.1 Enable OFF ON
OFF
4426 PT 108.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como Pt100. Pt100. O setpoint do Pt100 pode ser em deg. C ou Fahrenheit, dependendo da unidade de seleção (parâmetro 10970).
4430 Pt100 108.2
4431 PT 108.2 Setpoint -49 482
80
4432 PT 108.2 Delay 0.0 sec 999.0 sec
5.0 sec
4433 PT 108.2 Relay output A
Not used Option dep.
Not used
4434 PT 108.2 Relay output B
Not used Option dep.
Not used
4435 PT 108.2 Enable OFF ON
OFF
4436 PT 108.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como Pt100. Pt100. O setpoint do Pt100 pode ser em deg. C ou Fahrenheit, dependendo da unidade de seleção (parâmetro 10970).
4440 VDO oil 108.1
4441 VDO oil 108.1 Setpoint 0.0 145.0
4.0
4442 VDO oil 108.1 Delay 0.0 sec 999.0 sec
5.0 sec
4443 VDO oil 108.1 Relay output A
Not used Option dep.
Not used
4444 VDO oil 108.1 Relay output B
Not used Option dep.
Not used
4445 VDO oil 108.1 Enable OFF ON
OFF
4446 VDO oil 108.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como VDO pressao do oleo. O setpoint de pressão do oleo pode ser em Bar ou PSI, dependendo da unidade de seleção (parâmetro 10970).
4450 VDO oil 108.2
4451 VDO oil 108.2 Setpoint 0.0 145.0
5.0 Designers Reference
Uma multi-entrada 108 pode ser configurada
AGC-3 Alarm and Parameter List
DEIF A/S Page 50 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4452 VDO oil 108.2 Delay 0.0 sec 999.0 sec
5.0 sec
4453 VDO oil 108.2 Relay output A
Not used Option dep.
Not used
4454 VDO oil 108.2 Relay output B
Not used Option dep.
Not used
4455 VDO oil 108.2 Enable OFF ON
OFF
4456 VDO oil 108.2 Fail class F1…F7 Warning (F2)
Handbook como VDO pressao do oleo. O setpoint de pressão do oleo pode ser em Bar ou PSI, dependendo da unidade de seleção (parâmetro 10970).
4460 VDO water 108.1
4461 VDO water 108.1
Setpoint -49 482
100
4462 VDO water 108.1
Delay 0.0 sec 999.0 sec
5.0 sec
4463 VDO water 108.1
Relay output A
Not used Option dep.
Not used
4464 VDO water 108.1
Relay output B
Not used Option dep.
Not used
4465 VDO water 108.1
Enable OFF ON
OFF
4466 VDO water 108.1
Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como VDO temperatura da água. O setpoint de temperatura da água pode ser em C ou F, dependendo da unidade de seleção (parâmetro 10970).
4470 VDO water 108.2
4471 VDO water 108.2
Setpoint -49 482
110
4472 VDO water 108.2
Delay 0.0 sec 999.0 sec
5.0 sec
4473 VDO water 108.2
Relay output A
Not used Option dep.
Not used
4474 VDO water 108.2
Relay output B
Not used Option dep.
Not used
4475 VDO water 108.2
Enable OFF ON
OFF
4476 VDO water 108.2
Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como VDO temperatura da água. O setpoint de temperatura da água pode ser em C ou F, dependendo da unidade de seleção (parâmetro 10970).
4480 VDO fuel level 108.1
4481 VDO fuel 108.1 Setpoint 0% 100%
10%
4482 VDO fuel 108.1 Delay 0.0 sec 999.0 sec
10.0 sec
4483 VDO fuel 108.1 Relay output A
Not used Option dep.
Not used
4484 VDO fuel 108.1 Relay output B
Not used Option dep.
Not used
4485 VDO fuel 108.1 Enable OFF ON
OFF
4486 VDO fuel 108.1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como VDO de nível de combustível.
4490 VDO fuel level 108.2
AGC-3 Alarm and Parameter List
DEIF A/S Page 51 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4491 VDO fuel 108.2 Setpoint 0% 100%
10%
4492 VDO fuel 108.2 Delay 0.0 sec 999.0 sec
10.0 sec
4493 VDO fuel 108.2 Relay output A
Not used Option dep.
Not used
4494 VDO fuel 108.2 Relay output B
Not used Option dep.
Not used
4495 VDO fuel 108.2 Enable OFF ON
OFF
4496 VDO fuel 108.2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Uma multi-entrada 108 pode ser configurada como VDO de nível de combustível.
4500 Wire fail 108
4501 W. fail 108 Relay output A
Not used Option dep.
Not used
4502 W. fail 108 Relay output B
Not used Option dep.
Not used
4503 W. fail 108 Enable OFF ON
OFF
4504 W. fail 108 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A falha do fio desconectado é detectado e ativada.
Programar Velocidade e feedback de funcionamento
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4510 Sobrevelocidade 1
4511 Overspeed 1 Setpoint 100% 150%
110%
4512 Overspeed 1 Delay 0.0 sec 100.0 sec
5.0 sec
4513 Overspeed 1 Relay output A
Not used Option dep.
Not used
4514 Overspeed 1 Relay output B
Not used Option dep.
Not used
4515 Overspeed 1 Enable OFF ON
OFF
4516 Overspeed 1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A porcentagem é relative com a RPM nominal.
4520 Sobrevelocidade 2
4521 Overspeed 2 Setpoint 100% 150%
120%
4522 Overspeed 2 Delay 0.0 sec 100.0 sec
1.0 sec
4523 Overspeed 2 Relay output A
Not used Option dep.
Not used
4524 Overspeed 2 Relay output B
Not used Option dep.
Not used
4525 Overspeed 2 Enable OFF ON
OFF
Designers Reference Handbook
A porcentagem é relative com a RPM nominal.
AGC-3 Alarm and Parameter List
DEIF A/S Page 52 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4526 Overspeed 2 Fail class F1…F7 Warning (F2)
4530 Falha De Partida
4531 Crank failure Setpoint 1 RPM 400 RPM
50 RPM
4532 Crank failure Delay 0.0 sec 20.0 sec
2.0 sec
4533 Crank failure Relay output A
Not used Option dep.
Not used
4534 Crank failure Relay output B
Not used Option dep.
Not used
4535 Crank failure Enable OFF ON
OFF
4536 Crank failure Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se MPU é escolhido com prioridade do feedback de funcionamento, este alarme seria ativado se não estiver na determinada RPM no tempo programado.
4540 Falha Do Retorno De Funcionamento
4541 Run feedb. fail Delay 0.0 sec 20.0 sec
2.0 sec
4542 Run feedb. fail Relay output A
Not used Option dep.
Not used
4543 Run feedb. fail Relay output B
Not used Option dep.
Not used
4544 Run feedb. fail Enable OFF ON
ON
4545 Run feedb. fail Fail class F1…F7 Warning
(F2)
Designers Reference Handbook
Se a detecção de funcionamento está pela frequência (secundario), mas o primeiro feedback de funcionamento está , por exemplo, uma entrada digital, e não estiver detectado funcionamento, este alarme ocorreria depois do tempo programado.
4550 fio desconectado do pickup Magnetico
4551 MPU wirebreak Relay output A
Not used Option dep.
Not used
4552 MPU wirebreak Relay output B
Not used Option dep.
Not used
4553 MPU wirebreak Enable OFF ON
OFF
4554 MPU wirebreak Fail class F1…F7 Warning (F2)
Designers Reference Handbook
O monitoramento do fio desconectado esta apenas ativo quando o motor estiver parado.
4560 Falha de Hz/Tensão
4561 Hz/V failure Delay 1.0 sec 99.0 sec
30.0 sec
4562 Hz/V failure Relay output A
Not used Option dep.
Not used
4563 Hz/V failure Relay output B
Not used Option dep.
Not used
4564 Hz/V failure Enable OFF ON
ON
4565 Hz/V failure Fail class F1…F7 Block (F1)
Designers Reference Handbook
Se a frequência e a tensão não estiverem nos limites depois do feedback de funcionamento estar presente, este alarme estaria ativo quando o tempo programado expirar.
4570 Falha De Partida
AGC-3 Alarm and Parameter List
DEIF A/S Page 53 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4571 Start failure Relay output A
Not used Option dep.
Not used
4572 Start failure Relay output B
Not used Option dep.
Not used
4573 Start failure Fail class F1…F7 Block (F1)
Designers Reference Handbook
O alarme de falha na partida ocorrerá, se o gerador não estiver partido depois do número de tentativas de partida.
4580 Falha De Parada
4581 Stop failure Delay 10.0 sec 120.0 sec
30.0 sec
4582 Stop failure Relay output A
Not used Option dep.
Not used
583 Stop failure Relay output B
Not used Option dep.
Not used
4584 Stop failure Enable OFF ON
ON
4585 Stop failure Fail class F1…F7 Shutdown (F5)
Designers Reference Handbook
O alarme de falha na parade irá ocorrer se houver ainda status de funcionamento ou se houver tensão no gerador depois que o tempo estiver expirado.
Programar Alimentação
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4960 Baixa Tensão na alimentação terminal 1
4961 U< aux. term. 1 Setpoint 8.0 V DC 32.0 V DC
18.0 V DC
4962 U< aux. term. 1 Delay 0.0 sec 999.0 sec
1.0 sec
4963 U< aux. term. 1 Relay output A
Not used Option dep.
Not used
4964 U< aux. term. 1 Relay output B
Not used Option dep.
Not used
4965 U< aux. term. 1 Enable OFF ON
ON
4966 U< aux. term. 1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A alimentação nos terminais 1 e 2 são continuos se a tensão ficar abaixo do ajuste de setpoint no tempo programado ocorrerá um alarme.
4970 Alta Tensão na alimentação terminal 1
4971 U> aux. term. 1 Setpoint 12.0 V DC 36.0 V DC
30.0 V DC
4972 U> aux. term. 1 Delay 0.0 sec 999.0 sec
1.0 sec
4973 U> aux. term. 1 Relay output A
Not used Option dep.
Not used
4974 U> aux. term. 1 Relay output B
Not used Option dep.
Not used
4975 U> aux. term. 1 Enable OFF ON
ON
4976 U> aux. term. 1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A alimentação nos terminais 1 e 2 são continuos se a tensão passar do ajuste de setpoint no tempo programado ocorrerá um alarme.
AGC-3 Alarm and Parameter List
DEIF A/S Page 54 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
4980 Baixa Tensão na alimentação terminal 98
4981 U> aux. term. 98 Setpoint 8.0 V DC 32.0 V DC
18.0 V DC
4982 U> aux. term. 98 Delay 0.0 sec 999.0 sec
1.0 sec
4983 U> aux. term. 98 Relay output A
Not used Option dep.
Not used
4984 U> aux. term. 98 Relay output B
Not used Option dep.
Not used
4985 U> aux. term. 98 Enable OFF ON
ON
4986 U> aux. term. 98 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A alimentação nos terminais 98 e 99 são continuos se a tensão ficar abaixo do ajuste de setpoint no tempo programado ocorrerá um alarme.
4990 Alta Tensão na alimentação terminal 98
4991 U> aux. term. 98 Setpoint 8.0 V DC 32.0 V DC
30.0 V DC
4992 U> aux. term. 98 Delay 0.0 sec 999.0 sec
1.0 sec
4993 U> aux. term. 98 Relay
output A
Not used Option
dependent Not used
4994 U> aux. term. 98 Relay
output B
Not used Option
dependent Not used
4995 U> aux. term. 98 Enable OFF ON
ON
4996 U> aux. term. 98 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
A alimentação nos terminais 98 e 99 são continuos se a tensão passar do ajuste de setpoint no tempo programado ocorrerá um alarme.
AGC-3 Alarm and Parameter List
DEIF A/S Page 55 of 112
Alarmes De Comunicação Interna e Fio Desconectado Da Solenóide De Parada
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6270 fio desconectado da solenóide de parada
6271 Stop coil wirebreak
Relay output A
Not used Option dep.
Not used
6272 Stop coil wirebreak
Relay output B
Not used Option dep.
Not used
6273 Stop coil wirebreak
Enable OFF ON
OFF
6274 Stop coil wirebreak
Fail class F1…F7 Warning (F2)
Designers Reference Handbook
O monitoramento caso o fio esteja desconectado é apenas ativo quando a saída da solenóide de parada está desativada.
6280 Falha De Comunicação Interna
6281 Int. comm. fail Relay output A
Not used Option dep.
Not used
6282 Int. comm. fail Relay output B
Not used Option dep.
Not used
6283 Int. comm. fail Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Este alarme é para falha de comunicação entre o processador de rede e a interface do motor.
Falha De Aquecimento Do Motor
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6330 Aquecimento Do Motor 1
6331 Engine heater 1 Setpoint 10 deg 250 deg
30 deg
6332 Engine heater 1 Timer 1.0 sec 300.0 sec
10.0 sec
6333 Engine heater 1 Output A Not used Option dep.
Not used
6334 Engine heater 1 Output B Not used Option dep. Not used
6335 Engine heater 1 Enable OFF ON
OFF
6336 Engine heater 1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
AGC-3 Alarm and Parameter List
DEIF A/S Page 56 of 112
Teste De Bateria
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6410 Teste De Bateria
6411 Battery test Setpoint 8 V 32 V
18 V
6412 Battery test Timer 1 sec 300 sec
20 sec
6413 Battery test Relay output A
Not used Option dep.
Not used
6414 Battery test Relay output B
Not used Option dep.
Not used
6415 Battery test Enable OFF ON
OFF
6416 Battery test Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se a tesão da bateria cair abaixo do valor do setpoint durante o teste de partida, o alarme ativa
6420 Auto Teste De Bateria
6421 Auto batt test Enable On Off
Off
6422 Auto batt test Day Monday Sunday
Monday
6423 Auto batt test Hours 0 h 23 h
10h
6424 Auto batt test Week 1 52
53
6425 Auto batt test Relay Start relay Option dep.
Designers Reference Handbook
Teste automático da bateria na hora definida
6430 Bateria De Assimetria
6431 Batt. asymmetry T1 Power supply
Multi-input 108
Multi-input 105
6432 Batt. asymmetry RF1 Power supply
Multi-input 108
Power supply
6433 Batt. asymmetry T2 Power supply
Multi-input 108
Multi-input 108
6434 Batt. asymmetry RF2 Power supply
Multi-input 108
Multi-input 102
Designers Reference Handbook
Seleção de entrada assimetria da bateria
6440 Bateria De Assimetria 1
6441 Battery asym 1 Setpoint 0.1 V 15.0 V
1.0 V
6442 Battery asym 1 Timer 0.0 sec 10.0 sec
1.0 sec
6443 Battery asym 1 Relay output A
Not used Option dep.
Not used
6444 Battery asym 1 Relay output B
Not used Option dep.
Not used
6445 Battery asym 1 Enable OFF ON
OFF
Designers Reference Handbook
Se a tensão de assitria da bateria entre uma unica bareria exceder, o alarme ativa.
AGC-3 Alarm and Parameter List
DEIF A/S Page 57 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6446 Battery asym 1 Fail class F1…F7 Warning (F2)
6450 Bateria De Assimetria 2
6451 Battery asym 2 Setpoint 0.1 V 15.0 V
1.0 V
6452 Battery asym 2 Timer 0.0 sec 10.0 sec
1.0 sec
6453 Battery asym 2 Relay output A
Not used Option dep.
Not used
6454 Battery asym 2 Relay output B
Not used Option dep.
Not used
6455 Battery asym 2 Enable OFF ON
OFF
6456 Battery asym 2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se a tensão de assitria da bateria entre uma unica bareria exceder, o alarme ativa.
Maxima Ventilação
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6470 Max vent 1
6471 Max vent 1 Setpoint 20 deg 250 deg
95 deg
6472 Max vent 1 Timer 0.0 sec 60.0 sec
1.0 sec
6473 Max vent 1 Relay output A
Not used Option dep.
Not used
6474 Max vent 1 Relay output B
Not used Option dep.
Not used
6475 Max vent 1 Enable OFF ON
OFF
6476 Max vent 1 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se o ventilador de resfriamento deixar de funcionar e a temperatura de resfriamento ultrapassar o valor do setting, o alarme irá ativar
6480 Max vent 2
6481 Max vent 2 Setpoint 20 deg 250 deg
98 deg
6482 Max vent 2 Timer 0.0 sec 60.0 sec
1.0 sec
6483 Max vent 2 Relay output A
Not used Option dep.
Not used
6484 Max vent 2 Relay output B
Not used Option dep.
Not used
6485 Max vent 2 Enable OFF ON
OFF
6486 Max vent 2 Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se o ventilador de resfriamento deixar de funcionar e a temperatura de resfriamento ultrapassar o valor do setting, o alarme irá ativar
AGC-3 Alarm and Parameter List
DEIF A/S Page 58 of 112
Erro Switchboard
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6500 Block switchboard error
6501 Blk. Swbd error Setpoint 20 deg 250 deg
95 deg
6502 Blk. Swbd error Pararallel ON OFF
OFF
6503 Blk. Swbd error Relay output A
Not used Option dep.
Not used
6504 Blk. Swbd error Relay output B
Not used Option dep.
Not used
6505 Blk. Swbd error Enable OFF ON
OFF
6506 Blk. Swbd error Fail class F1…F7 Warning (F2)
Designers Reference Handbook
Se a entrada binária “switchboard error” ativa, o gerador parado será bloqueado para partida. Parâmetro 6502: OFF: Só a partida AMS é afetada ON: toda partida será afetada.
6510 Stop switchboard error
6511 Stp. Swbd error Timer 0.0 sec 999.0 sec
1.0 sec
6512 Stp. Swbd error Relay output A
Not used Option dep.
Not used
6513 Stp. Swbd error Relay output B
Not used Option dep.
Not used
6514 Stp. Swbd error Enable OFF ON
OFF
6515 Stp. Swbd error Fail class F1…F7 Shutdown (F5)
Designers Reference Handbook
Se a entrada binária de "switchboard erro" activa, o gen-definido será interrompido.
Erro Switchboard
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6540 Não esta em AUTO
6541 Not in auto Timer 10.0 sec 900.0 sec
300.0 sec
6542 Not in auto Relay output A
Not used Option dep.
Not used
6543 Not in auto Relay output B
Not used Option dep.
Not used
6544 Not in auto Enable OFF ON
OFF
6545 Not in auto Fail class F1…F7 Warning (F2)
Designers Reference Handbook
AGC-3 Alarm and Parameter List
DEIF A/S Page 59 of 112
Erro De Comunicação Externa
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7520 Erro De Comunicação Externa
7521 Ext. comm. error
Delay 1.0 s 100.0 s
10.0 s
7522 Ext. comm. error
Relay output A
R0 Option dep.
R0 (none)
7523 Ext. comm. error
Relay output B
R0 Option dep.
R0 (none)
7524 Ext. comm. error
Enable OFF ON
OFF
7525 Ext. comm. error
Fail class F1…F7 Warning (F2)
Opção: Modbus
(H2) Profibus
(H3)
Supervisão da linha de comunicação externa. O alarme ira ocorrer quando não tenha avido qualquer comunicação durante o tempo determinado (delay).
7530 ID De Comunicação Interna
7532 Int. comm. ID CAN fail.
mode Manual
No mode change
Manual
7533 Int. comm. ID Missing all units
F1…F7 Warning (F2)
7534 Int. comm. ID Fatal CAN error
F1…F7 Warning (F2)
7535 Int. comm. ID Any
G/SG/SC/BA missing
F1…F7 Warning
(F2)
7536 Int. comm. ID Any mains missing
F1…F7 Warning (F2)
Designers Reference Handbook
Falha na CAN, módos disponíveis
- Manual - Semi-Auto - No mode change
AGC-3 Alarm and Parameter List
DEIF A/S Page 60 of 112
Alarmes De Comunicação De Interface Do Motor
No.
Setting Min.
Max.
Factory setting
Notes Ref. Description
7570 EI comm. Error
7571 EI comm. error Timer
0.0 s
100.0 s 0.0 s
7572 EI comm. error Relay A
Not used
Option dep. Not used
7573 EI comm. error Relay B
Not used
Option dep. Not used
7574 EI comm. error Enable
OFF
ON ON
7575 EI comm. error Fail class F1…F7 Warning (F2)
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7)
Supervisão da linha de comunicação com EIC. O alarme ira ocorrer quando não tenha avido qualquer comunicação durante o tempo determinado (delay).
7580 EIC warning
7581 EIC warning Timer
0.0 s
100.0 s 0.0 s
7582 EIC warning Relay A
Not used
Option dep. Not used
7583 EIC warning Relay B
Not used
Option dep. Not used
7584 EIC warning Enable
OFF
ON ON
7585 EIC warning Fail class F1…F7 Warning (F2)
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7))
7590 EIC shutdown
7591 EIC shutdown Timer
0.0 s
100.0 s 0.0 s
7592 EIC shutdown Relay A
Not used
Option dep. Not used
7593 EIC shutdown Relay B
Not used
Option dep. Not used
7594 EIC shutdown Enable
OFF
ON ON
7595 EIC shutdown Fail class F1…F7 Warning (F2)
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7)
7600 EIC overspeed
AGC-3 Alarm and Parameter List
DEIF A/S Page 61 of 112
No.
Setting Min.
Max.
Factory setting
Notes Ref. Description
7601 EIC overspeed Setpoint
0%
400% 107 %
7602 EIC overspeed Timer
0.0 s
100.0 s 2.0 s
7603 EIC overspeed Relay A
Not used
Option dep. Not used
7604 EIC overspeed Relay B
Not used
Option dep. Not used
7605 EIC overspeed Enable
OFF
ON ON
7606 EIC overspeed Fail class F1…F7 Warning (F2)
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7))
7610 EIC coolant temp. 1
7611 EIC coolant t. 1 Setpoint
-40 deg
210 deg 100 deg
7612 EIC coolant t. 1 Timer
0.0 s
100.0 s 5.0 s
7613 EIC coolant t. 1 Relay A
Not used
Option dep. Not used
7614 EIC coolant t. 1 Relay B
Not used
Option dep. Not used
7615 EIC coolant t. 1 Enable
OFF
ON ON
7616 EIC coolant t. 1 Fail class F1…F7 Warning (F2)
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7)
7620 EIC coolant temp. 2
7621 EIC coolant t. 2 Setpoint
-40 deg
210 deg 110 deg
7622 EIC coolant t. 2 Timer
0.0 s
100.0 s 5.0 s
7623 EIC coolant t. 2 Relay A
Not used
Option dep. Not used
7624 EIC coolant t. 2 Relay B
Not used
Option dep. Not used
7625 EIC coolant t. 2 Enable
OFF
ON ON
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7)
AGC-3 Alarm and Parameter List
DEIF A/S Page 62 of 112
No.
Setting Min.
Max.
Factory setting
Notes Ref. Description
7626 EIC coolant t. 2 Fail class F1…F7 Warning (F2)
7630 EIC oil pressure 1
7631 EIC oil press. 1 Setpoint
0 bar
10 bar 2 bar
7632 EIC oil press. 1 Timer
0.0 s
100.0 s 5.0 s
7633 EIC oil press. 1 Relay A
Not used
Option dep. Not used
7634 EIC oil press. 1 Relay B
Not used
Option dep. Not used
7635 EIC oil press. 1 Enable
OFF
ON ON
7636 EIC oil press. 1 Fail class F1…F7 Warning (F2)
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7)
7640 EIC oil pressure 2
7641 EIC oil press. 2 Setpoint
0 bar
10 bar 1 bar
7642 EIC oil press. 2 Timer
0.0 s
100.0 s 5.0 s
7643 EIC oil press. 2 Relay A
Not used
Option dep. Not used
7644 EIC oil press. 2 Relay B
Not used
Option dep. Not used
7645 EIC oil press. 2 Enable
OFF
ON ON
7646 EIC oil press. 2 Fail class F1…F7 Warning (F2)
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7)
7650 EIC oil temp 1
7651 EIC oil temp. 1 Setpoint
0 deg.
300 deg 40 deg.
7652 EIC oil temp. 1 Timer
0.0 s
100.0 s 5.0 s
7653 EIC oil temp. 1 Relay A
Not used
Option dep. Not used
7654 EIC oil temp. 1 Relay B
Not used
Option dep. Not used
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7)
AGC-3 Alarm and Parameter List
DEIF A/S Page 63 of 112
No.
Setting Min.
Max.
Factory setting
Notes Ref. Description
7655 EIC oil temp. 1 Enable
OFF
ON ON
7656 EIC oil temp. 1 Fail class F1…F7 Warning (F2)
7660 EIC oil temp 2
7661 EIC oil temp. 2 Setpoint
0 deg.
300 deg 40 deg.
7662 EIC oil temp. 2 Timer
0.0 s
100.0 s 5.0 s
7663 EIC oil temp. 2 Relay A
R0
Option dep. R0 (none)
7664 EIC oil temp. 2 Relay B
Not used
Option dep. Not used
7665 EIC oil temp. 2 Enable
Not used
Option dep. Not used
7666 EIC oil temp. 2 Fail class F1…F7 Warning (F2)
Opção: J1939 e
MTU ADEC/ MDEC (H5)
Cummins Modbus
(H6)
J1939 (H7)
Erro De Comunicação Do Gerenciador De Potência
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7870 Any BTB missing/appl hazard
7871 Any BTB missing Failclass F1…F7 Block (F1)
7872 Appl hazard Enable ON OFF
OFF
7873
Appl hazard Failclass
F1…F7 Block (F1)
Designers Reference Handbook
O alarme “Any BTB missing” é ativo quando qualquer unidade BTB falhar O alarme application hazard é ativo, se as aplicações progamadas no controle forem diferentes.
AGC-3 Alarm and Parameter List
DEIF A/S Page 64 of 112
Erro De Comunicação Interna CAN
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7930 CAN1 communication error
7931 CAN1 com error Delay 2.0 s 600.0 s
10.0 s
7932 CAN1 com error Relay output A
R0 Option dep.
R0 (none)
7933 CAN1 com error Relay output B
R0 Option dep.
R0 (none)
7934 CAN1 com error Enable OFF ON
OFF
7935 CAN1 com error Failclass F1…F7 Block (F1)
Opção: External I/O
modules (H8.2)
Se as opções H8.x ambas estão presentes, um erro em qualquer dessas vai ativar o alarme. �
7940 CAN2 comm error
7941 CAN2 comm error Delay 2.0 s 600.0 s
10.0 s
7942 CAN2 comm error Relay output A
Not used Option dep.
Not used
7943 CAN2 comm error Relay output B
Not used Option dep.
Not used
7944 CAN2 comm error Enable OFF ON
OFF
7945 CAN2 comm error Failclass F1…F7 Block (F1)
Opção: External I/O
modules (H8.8)
Se as opções H8.x ambas estão presentes, um erro em qualquer dessas vai ativar o alarme.
Programar Alarme De I/O Externo
Entradas Analógicas
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
12000 Ext. Ain 1.1
Ext. Ain 1.1 Setpoint -20000 20000
10
Ext. Ain 1.1 Delay 2.0 s 600.0 s
10.0 s
Ext. Ain 1.1 Fail class F1…F7 Warning (F2)
Ext. Ain 1.1 Relay A R0 Option dep.
R0 (none)
Ext. Ain 1.1 Relay B R0 Option dep.
R0 (none)
Ext. Ain 1.1 Enable OFF ON
OFF
Option: External I/O
modules (H8.x)
Os alarmes baseados em módulos externos I / O apenas podem ser configurados usando o PC Utility Software.
AGC-3 Alarm and Parameter List
DEIF A/S Page 65 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
12010 Ext. Ain 1.2
Ext. Ain 1.2 Setpoint -20000 20000
10
Ext. Ain 1.2 Delay 2.0 s 600.0 s
10.0 s
Ext. Ain 1.2 Fail class F1…F7 Warning (F2)
Ext. Ain 1.2 Relay A R0 Option dep.
R0 (none)
Ext. Ain 1.2 Relay B R0 Option dep.
R0 (none)
Ext. Ain 1.2 Enable OFF ON
OFF
Option: External I/O
modules (H8.x)
Entradas Digitais
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
12540 Ext. dig. in 1
Ext. dig. in 1 Delay 2.0 s 600.0 s
10.0 s
Ext. dig. in 1 Fail class F1…F7 Warning (F2)
Ext. dig. in 1 Relay A R0 Option dep.
R0 (none)
Ext. dig. in 1 Relay B R0 Option dep.
R0 (none)
Ext. dig. in 1 Enable OFF ON
OFF
Option: External
I/O modules (H8.x)
A mesma ordem de definições entradas analógicas externas 2-8, configuráveis 12030-12220.
A mesma ordem de definições entradas analógicas externas 2-16, settings 12550-12690.
AGC-3 Alarm and Parameter List
DEIF A/S Page 66 of 112
4. Lista De Parâmetros A lista de parâmetros contém as definições para os reguladores e outras definições relacionadas com o não-alarme.
Tabela De Parâmetros Controle - Programar Gerador - Sincronismo 6190 Start attempts 2000 Sync. Type 6200 Shutdown override 2020 Dynamic sync. 6210 STOP 2030 Static sync. 6220 Hz/V OK 2040 f sync. Control Analogue 6230 GB/MB/BTB control 2050 f sync. control Relay 2060 Phase sync. Control Analogue 6260 Power derate 2070 Phase sync. control relay 6290 Idle start 2110 Sync. Blackout 6320 Engine heater 2240 Separate sync relay 2250 Close before excitation 6380 Loadshare out 2260 Breaker Sequence 6390 Loadshare type - Reguladores 6400 Master Clock 2510 Frequency control analogue 2530 Power control analogue 6460 Max ventilation 2540 Power load sharing control analogue 2550 Analogue gov. offset 6490 Summer/winter time 2570 f control relay 6520 Start next generator 2580 P control relay 6530 Stop next generator 2590 Load sharing control relay 2600 Relay control 6550 Fuel transfer pump logic 2610 Power ramp up 2620 Power ramp down 2640 Voltage control analogue 2650 Reactive power control analogue - Programar Rede 2660 Reactive power load sharing control analogue 7000 Mains power 2670 Analogue AVR output offset 7010 Daytime period 7020 Start generator 2690 U control relay 7030 Stop generator 2700 Q control relay 7040 Test 2710 Q load sharing control relay 7050 Controller settings 2720 Relay control (AVR) 7060 U mains failure 7070 f mains failure 2740 Delay reg. 7080 Mains breaker control 2760 Overlap 7130 CAN fail mode 2770 EIC speed control 2780 Reg. output -Comunicação externa 7500 communication control 7510 External communication - Programar Saídas 5000 Relay 05 - Comunicação interna do gerenciador de
potência.
5010 Relay 08 5020 Relay 11 7530 Internal communication ID 5030 Relay 14
AGC-3 Alarm and Parameter List
DEIF A/S Page 67 of 112
5040 Relay 17 - Engine interface communication 5050 Relay 20 5060 Relay 21 7560 Engine I/F 5110 Relay 57 -Programar comunicação de I/O externo 5120 Relay 59 7950 KL 320x setup 5130 Relay 61 7970 CAN 1 5140 Relay 63 7980 CAN 2 5150 Relay 65 7990 Event printer 5160 Relay 67 5170 Relay 69 -Programar gerenciador de potência 5180 Relay 71 5190 Relay 90 8000 Load dependent start 5200 Relay 92 8010 Load dependent stop 5210 Relay 94 8020 Start/stop selection 5220 Relay 96 8030 Priority selection 5230 Relay 126 5240 Relay 128 8080 Priority (1-5) 5250 Relay 130 8090 Priority (6-11) 5260 Relay 132 8100 Priority (12-16) 5270 Transistor setup 8110 Running hours 8120 Ground relay -saída analógica 8140 Stop non-connected generators 5720 PWM 68 limits 8170 Fuel optimize 5780 Aout 66 limits 5790 Aout 71 limits 8220 Avail. Power 1 5800 Aout 91 limits 8230 Avail. Power 2 5810 Aout 95 limits 8240 Avail. Power 3 8250 Avail. Power 4 -saída de transdutor 8260 Avail. Power 5 5820 P output 1 5830 P output 2 5840 P output 3 -Jump menus 5850 S output 9000 Software version 5860 Q output 9010 Display character test 5870 PF output 9020 Service port 5880 f output 9070 M4 SW version 5890 U output 5900 I output 9100 Device type 5910 U BB output 911X User password 5920 f BB output 9120 Service menu 5930 Multi-input 102 9130 AC config. 5940 Multi-input 105 9140 Angle compensation BB/G 5950 Multi-input 108 9150 Backlight dim 5960 P total consumed 9160 Application 5970 P total available 9170 Internal CAN protocol -Programar saída analogical do regulador 5980 Governor output - Comandos horários 5990 AVR output 10000 – 10310 Cmd timer 1 - 8 Sistema - Utility Software - Programar gerador 10320 GSM pin code 6000 Nom. Settings 1 10330 – 10370 Telephone no. 1-5 6010 Nom. Settings 2 6020 Nom. Settings 3 10390 Password Language page 6030 Nom. Settings 4 10400 Password log page 6040 G/M/BA transformer 10410 Password control page 6050 BB transformer 10970 Engineering units 6070 Gen-set Mode 10980 Multi inp. Conf. 102 6080 Language 10990 Multi inp. Conf. 105 11000 Multi inp. Conf. 108 6100 Counters
AGC-3 Alarm and Parameter List
DEIF A/S Page 68 of 112
6110 Service timer 1 - Entradas VDO 6120 Service timer 2 10460 – 10620 VDO 102 6130 Alarm horn 10630 – 10790 VDO 105 6160 Run status 10800 – 10960 VDO 108 6170 Running detect. 6180 Starter -Saídas digitais externa 12790-12940 Ext. dig. out - status dos módulos externos 12950-12980 Ext module STATUS
AGC-3 Alarm and Parameter List
DEIF A/S Page 69 of 112
Sincronização
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2000 Tipo De Sincronismo
2001 Sync. type Type Static
Dynamic Dynamic
Designers Reference Handbook
Sincr estático visa uma diferença de freqüência 0 Hz Sincr dinâmico visa uma frequência diferença (ponto médio entre a configuração 2021 dfMax. DfMin e 2022).
2020 Sincronização Dinâmica
2021 Dynamic sync.
dfMax. 0.0Hz 0.5Hz
0.2Hz
2022 Dynamic sync.
dfMin. -0.5Hz 0.3Hz
0.0Hz
2023 Dynamic sync.
dUMax. 2% 10%
5%
2024 Dynamic sync.
Sync t. GB/BTB/TB
40ms 300ms
50ms
2025 Dynamic sync.
Sync t. MB 40ms 300ms
50ms
Designers Reference Handbook
O setting 2020 só está disponível se Sincro Dinâmico estiver selecionado na configuração 2001
2030 Sincronização Dinâmica
2031 Static sync. dfMax. 0.00Hz 0.50Hz
0.10Hz
2032 Static sync. dUMax 2% 10%
5%
2033 Static sync. Close window 0.1 deg 20.0 deg
10.0 deg
2034 Static sync. Delay 0.1 s 99 s
1.0 s
Designers Reference Handbook
O setting 2030 só está disponível se Sincro Estático estiver selecionado na configuração 2001
2040 f sincronismo analógico
2041 f sync f Kp 0.00 60.00
0.50
2042 f sync f Ti 0.00 s 60.00 s
5.00 s
2043 f sync f Td 0.00 s 2.00 s 0.00 s
Option E1, E2,
EF2, EF4. EF5
Controlador PID para o Sincro dinâmico. Esta configuração está disponível somente se o "analógico" ou "PWM" ou "EIC" estiver selecionado na configuração 2780
2050 relé de controle de frequência de sincronismo
2051 f sync Kp 0 100
10
Designers Reference Handbook
Esta configuração está disponível somente se o "relay" está selecionado na configuração 2780
2060 Fase de sincronismo analógico
AGC-3 Alarm and Parameter List
DEIF A/S Page 70 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2061 Phase sync Phase Kp 0.00 60.00
0.50
2062 Phase sync Phase Ti 0.00 s 60.00 s
5.00 s
2063 Phase sync Phase Td 0.00 s 2.00 s 0.00 s
Designers Reference Handbook
Controle de PID para sincronismo estático Esta configuração está disponível somente se o "analógico" ou "PWM" ou "EIC" estiver selecionado na configuração 2780
2070 Relé de controle de fase
2071 Phase Kp 0 100
10
Designers Reference Handbook
Esta configuração está disponível somente se o "relay" está selecionado na configuração 2780
2110 Synchronisation blackout
2111 Sync. Blackout
dfMax. 0.0Hz 5.0Hz
3.0Hz
2112
Sync. Blackout
dUMax 2% 10% 5%
Designers Reference Handbook
Settings são limites aceitos para o fechamento do disjuntor, referindo-se a freqüência e tensão nominal.
2240 Separate synchronisation relay
2241 Sep sync relay
Output A Not used Option dep.
Not used
2242 Sep sync relay
Output B Not used Option dep.
Not used
Designers Reference Handbook
A saída ativa durante a sincronização, e separa de uma unidade de sincronismo externa.
2250 Close before excitation 2251 Close bef.
Exc. Setpoint 0 rpm
4000 rpm 400 rpm
2252 Close bef. Exc.
Timer 0.0 sec 999,0 sec
5.0 sec
2253 Close bef. Exc.
Output A Not used Option dep.
Not used
2554 Close bef. Exc.
Enable OFF ON
OFF
Designers Reference Handbook
Se definir a função irá fechar o disjuntor na velocidade seleccionada. O relé de saída é utilizado para a excitação sinal fechamento. Lembre-se de definir o relé selecionado em modo "Limite" .
2260 Sequência do disjuntor
2261 Breaker seq. Break Close GB
Close GB+TB
Close GB
2262 Breaker seq. Timer 0.0 sec 999.0 sec
5.0 sec
2263 Breaker seq. RpmOK 0 rpm 4000 rpm
1450 rpm
Designers reference handbook
A seqüência é utilizado para a função closed before excitation. A excitação será ativada na velocidade selecionada.
Reguladores
AGC-3 Alarm and Parameter List
DEIF A/S Page 71 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2510 Controle analógico de Frequencia
2511 f control f Kp 0.00 60.00
0.50
2512 f control f Ti 0.00 s 60.00 s
5.00 s
2513 f control f Td 0.00 s 2.00 s
0.00 s
Designers reference handbook
Controlador PID para o controle de frequência. Este menu só está disponível se 'analógico' estiver selecionado no menu 2781
2530 Controle analógico de Potência
2531 P control P Kp 0.00 60.00
0.50
2532 P control P Ti 0.00 s 60.00 s
5.00 s
2533 P control P Td 0.00 s 2.00 s
0.00 s
Designers Reference Handbook
Controlador PID para o controle de frequência. Este menu só está disponível se 'analógico' estiver selecionado no menu 2781
2540 Controle analógico de Divisão de carga
2541 P LS control P LS Kp 0.00 60.00
0.50
2542 P LS control P LS Ti 0.00 s 60.00 s
5.00 s
2543 P LS control P LS Td 0.00 s 2.00 s
0.00 s
Designers reference handbook
Controlador PID para o controle load sharing. Este menu só está disponível se 'analógico' estiver selecionado no menu 2781
2550 Analogue governor offset
2551 Analogue GOV Offset 0 % 100 %
50 %
Designers reference handbook
Controlador PID para o controle load sharing. Este menu só está disponível se 'analógico' estiver selecionado no menu 2781
2570 Saída do relé de controle de Frequencia
2571 f control relay Deadband 0.2% 10.0%
2.0%
2572 f control relay Kp 0 100
10
Designers Reference Handbook
Este menu só está disponível se 'analógico' estiver selecionado no menu 2781
2580 Saída do relé de controle de Potência
2581 P control relay Deadband 0.2% 10.0%
1.0%
2582 P control relay Kp 0 100
10
Designers Reference Handbook
Este menu só está disponível se 'analógico' estiver selecionado no menu 2781
2590 Saída do relé de controle de Divisão de carga 2591 LS ctrl. relay f deadband 0.2%
10.0% 1.0%
2592 LS ctrl. relay LS Kp 0 100
10
Designers Reference Handbook
Este menu só está disponível se 'analógico' estiver selecionado no menu
AGC-3 Alarm and Parameter List
DEIF A/S Page 72 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2593 LS ctrl. relay P deadband 0.2% 10.0%
2.0%
2594 LS ctrl. relay P weight 0.0 % 100.0 %
10.0 %
2781
2600 Relé de controle
2601 Relay control GOV ON time
10 ms 6500 ms
500 ms
2602 Relay control GOV period time
50 ms 32500 ms
2500 ms
2603 Relay control Increase relay
Not used Option
dependent Not used
2604 Relay control Decrease relay
Not used Option
dependent Not used
Designers Reference Handbook
Este menu só está disponível se 'analógico' estiver selecionado no menu 2781
2610 Rampa de subida de potência
2611 Power ramp up Speed 0.1%/s 20.0%/s
2.0%/s
2612 Power ramp up Delay point 1% 100%
10%
2613 Power ramp up Delay time 0.0 sec
990.0 sec 10.0 sec
Designers Reference Handbook
O delay point determina quando o gerador vai fazer uma parada temporária com rampa, após o fechamento do disjuntor do gerador, para o pré-aquecimento do motor antes de iniciar e assumir a carga. Se delay point não é necessário, definir esse tempo para 0. A configurações% da potência referem-se a uma potência nominal.
2620 Rampa de descida de potência
2621 Power ramp down
Speed 0.1%/s 20.0%/s
10.0%/s
2623 Power ramp down
Breaker open point
1% 20%
5%
Designers Reference Handbook
O ponto de abertura do disjuntor determina quando o "disjuntor abre" o relé de saída é ativado para abrir o disjuntor dogerador antes de chegar a 0 kW. A configurações% da potência referem-se a uma potência nominal.
2640 Controle analógico de tensão
2641 U control U Kp 0.00 60.00
0.50
2642 U control U Ti 0.00 s 60.00 s
5.00 s
Opção: controle
AVR (D1)
Controlador PID para controle de tensão. Este menu só está disponível se saída
AGC-3 Alarm and Parameter List
DEIF A/S Page 73 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2643 U control U Td
0.00 s 2.00 s 0.00 s
analógica estiver selecionada no menu 2782
2650 Controle analógico de Potência Reativa
2651 Q control Q Kp 0.00 60.00
0.50
2652 Q control Q Ti 0.00 s 60.00 s
5.00 s
2653 Q control Q Td
0.00 s 2.00 s
0.00 s
Opção: controle
AVR (D1)
Controlador PID para o controle de potência reativa . A potência reativa é usada para controlar factor de potência, bem como o controle de potência reativa . Este menu só está disponível se saída analógica estiver selecionada no menu 2782
2660 Controle analógico de de divisão de carga de Potência Reativa
2661 Q load sh. ctrl Q LS Kp 0.00 60.00
5.00
2662 Q load sh. ctrl Q LS Ti 0.00 s 60.00 s
5.00 s
2663 Q load sh. ctrl Q LS Td 0.00 s 2.00 s
0.00 s
2664 Q load sh. ctrl Q weight
0.0% 100.0%
10.0%
Opção: controle
AVR (D1)
O Var (Q) load sharing baseia-se num misto de tensão e controle var . A configuração 2664 está a definir o impacto da Var controlador de tensão durante o tratamento. Este menu só está disponível se saída analógica estiver selecionada no menu 2782
2670 Offset Saída Analógica do AVR
2671 Analogue AVR Offset -100 % +100%
0 %
Opção: controle
AVR (D1/D2)
Parâmetro 2671 define o offset da saída analógica quando se inicia o gerador. Este menu só está disponível se saída analógica estiver selecionada no menu 2782
2690 Relé de controle de Tensão
2691 U control U DB 0.0 % 10.0 %
2.0 %
2692 U control U Kp
0.0 100.0 2.0
Opção: controle
AVR (D1/D2)
O controle PI para controle de tensão. Este menu só está disponível se "relay" estiver selecionado no menu 2782
2700 Relé de controle de Potência Reativa
2701 Q control Q DB 0.0 % 10.0 %
2.0 % Opção: controle
O controle PI para controle potência
AGC-3 Alarm and Parameter List
DEIF A/S Page 74 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2702 Q control Q Kp 0.0
100.0 2.0 s
AVR (D1)
reativa. A potência reativa é usada para controlar o fator de potência, bem como o controle energia reativa. Este menu só está disponível se "relay" estiver selecionado no menu 2782
2710 Relé de controle de Divisão de Potência Reativa
2711 Q load sh. ctrl U deadband 0.0 % 10.0 %
1.0 %
2712 Q load sh. ctrl U Kp 0.0 100.0
10.0
2713 Q load sh. ctrl Q deadband 0.0 % 10.0 %
2.0 %
2714 Q load sh. ctrl Q weight 0.0 100.0
2.0 s
Opção: controle
AVR (D1)
O Var (Q) load sharing baseia-se num misto de tensão e controle var . A configuração 2664 está a definir o impacto da Var controlador de tensão durante o tratamento. Este menu só está disponível se saída analógica estiver selecionada no menu 2782
2720 Programar controle de relé (AVR)
2721 Relay control AVR ON time tN
10 ms 3000 ms
100 ms
2722 Relay control AVR per time tP
50 ms 1500 ms
500 ms
2723 Relay control U increase R0
Option dep.
R0
2724 Relay control U decrease R0
Option dep.
R0
Opção: controle
AVR (D1)
Relé de saídas de controle de tensão / var / fator de potência . Este menu só está disponível se "relay" estiver selecionado no menu 2782
2740 Tempo dos Reguladores
2741 Delay reg. Delay 0 sec 9900 sec
0 sec
2742 Delay reg. Relay output A
Not used Option
dependent Not used
2743 Delay reg. Relay output B
Not used Option
dependent Not used
2744 Delay reg. Enable OFF ON
OFF
Designers Reference Handbook
Dalay reg é o tempo de espera antes de sincronizar o motor depois de ter começado. Ela é usada quando o motor precisa de estabilizar após o início antes de tentar sincronizar.
2760 Troca
2761 Overlap Enable OFF ON
OFF Designers Reference
Se definido no gerador a alimentação
AGC-3 Alarm and Parameter List
DEIF A/S Page 75 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
2762 Overlap Timer 0.1 sec 99.9 sec 0.3 sec
Handbook do disjuntor, nunca ambos devem ser fechados por um período de tempo mais longo do que o selecionado .
2770 EIC speed control
2771 Scania control Droop 0.0 %
25.0 % 4.0 %
2772 Scania control rpm User 1500 RPM 1800 RPM Low idle
User
Only available if ‘Scania’ is selec-ted in menu 7561
2773 Cummins Gain Kp 0.00
10.00 5.00
Only available when ‘Cum-mins’ is selected in menu 7561.
Option: J1939 (H5 or
H7)
Configuração do controlo de velocidade do motor através da interface de comunicação.
2780 Saída Do Regulador
2781 Reg. output GOV Relay EIC
Relay
Designers Reference Handbook
Seleção da saída de velocidade : relé, analógica ou interface de comunicação com motor. Analógico e EIC são opções dependentes.
2782 Reg. output AVR Relay
Analogue
Relay
Option: AVR
control (D1/D2)
O controle de tensão do gerador é baseado em relé ou saída de sinais analógicos A seleção analógica só está disponível se opção E1, E2, EF2, EF4 ou F2 estiver presente
AGC-3 Alarm and Parameter List
DEIF A/S Page 76 of 112
Programar Saída Digital
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5000 Relay 05
5001 Relay 05 Function Alarm Horn
Alarm
5002 Relay 05 OFF delay 0.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5010 Relay 08
5011 Relay 08 Function Alarm Horn
Alarm
5012 Relay 08 OFF delay 1.0 sec 999.9 sec 0.0 sec
Designers Reference Handbook
Seleção de funções:
- Alarme - Limite - Sirene
5020 Relay 11
5021 Relay 11 Function Alarm Horn
Alarm
5022 Relay 11 OFF delay 2.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5030 Relay 14
5031 Relay 14 Function Alarm Horn
Alarm
5032 Relay 14 OFF delay 3.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5040 Relay 17
5041 Relay 17 Function Alarm Horn
Alarm
5042 Relay 17 OFF delay 4.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5050 Relay 20
5051 Relay 20 Function Alarm Horn
Alarm
5052 Relay 20 OFF delay 5.0 sec 999.9 sec 0.0 sec
Designers Reference Handbook
Seleção de funções:
- Alarme - Limite - Sirene
5060 Relay 21
5061 Relay 21 Function Alarm Horn
Alarm
5062 Relay 21 OFF delay 6.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5110 Relay 57
5111 Relay 57 Function Alarm Horn
Alarm
5112 Relay 57 OFF delay 7.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5120 Relay 59
AGC-3 Alarm and Parameter List
DEIF A/S Page 77 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5121 Relay 59 Function Alarm Horn
Alarm
5122 Relay 59 OFF delay 8.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5130 Relay 61
5131 Relay 61 Function Alarm Horn
Alarm
5132 Relay 61 OFF delay 9.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5140 Relay 63
5141 Relay 63 Function Alarm Horn
Alarm
5142 Relay 63 OFF delay 10.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5150 Relay 65
5151 Relay 65 Function Alarm Horn
Alarm
5152 Relay 65 OFF delay 11.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Normalmente utilizado para comando UP do governador (menu 2600). Seleção de funções:
- Alarme - Limite - Sirene
5160 Relay 67
5161 Relay 67 Function Alarm Horn
Alarm
5162 Relay 67 OFF delay 12.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Normalmente utilizado para comando DOWN do governador (menu 2600). Seleção de funções:
- Alarme - Limite - Sirene
5170 Relay 69
5171 Relay 69 Function Alarm Horn
Alarm
5172 Relay 69 OFF delay 13.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5180 Relay 71
5181 Relay 71 Function Alarm Horn
Alarm
5182 Relay 71 OFF delay 14.0 sec 999.9 sec
0.0 sec
Designers Reference Handbook
Seleção de funções: - Alarme - Limite - Sirene
5190 Relay 90
5191 Relay 90 Function Alarm Limit Horn
Alarm
5192 Relay 90 OFF delay 0.0 s 999.9 s
5.0 s
Option: 4 x relay
output, slot #6
(M14.6)
Seleção de funções: - Alarme - Limite - Sirene
5200 Relay 92
AGC-3 Alarm and Parameter List
DEIF A/S Page 78 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5201 Relay 92 Function Alarm Limit Horn
Alarm
5202 Relay 92 OFF delay 1.0 s 999.9 s
5.0 s
Option: 4 x relay
output, slot #6
(M14.6)
Seleção de funções: - Alarme - Limite - Sirene
5210 Relay 94
5211 Relay 94 Function Alarm Limit Horn
Alarm
5212 Relay 94 OFF delay 2.0 s 999.9 s
5.0 s
Option: 4 x relay
output, slot #6
(M14.6)
Seleção de funções: - Alarme - Limite - Sirene
5220 Relay 96
5221 Relay 96 Function Alarm Limit Horn
Alarm
5222 Relay 96 OFF delay 3.0 s 999.9 s
5.0 s
Option: 4 x relay
output, slot #6
(M14.6)
Seleção de funções: - Alarme - Limite - Sirene
5230 Relay 126
5231 Relay 126 Function Alarm Limit Horn
Alarm
5232 Relay 126 OFF delay 4.0 s 999.9 s
5.0 s
Option: 4 x relay
output, slot #8
(M14.8)
Seleção de funções: - Alarme - Limite - Sirene
5240 Relay 128
5241 Relay 128 Function Alarm Limit Horn
Alarm
5242 Relay 128 OFF delay 5.0 s 999.9 s
5.0 s
Option: 4 x relay
output, slot #8
(M14.8)
Seleção de funções: - Alarme - Limite - Sirene
5250 Relay 130
5251 Relay 130 Function Alarm Limit Horn
Alarm
5252 Relay 130 OFF delay 6.0 s 999.9 s
5.0 s
Option: 4 x relay
output, slot #8
(M14.8)
Seleção de funções: - Alarme - Limite - Sirene
5260 Relay 132
5261 Relay 132 Function Alarm Limit Horn
Alarm
5262 Relay 132 OFF delay 7.0 s 999.9 s
5.0 s
Option: 4 x relay
output, slot #8
(M14.8)
Seleção de funções: - Alarme - Limite - Sirene
5270 Transistor output setup
5271 Transistor 20 T20 Relay kWh Relay
Designers Reference Handbook
O transistor de saída nos terminais 21 e 22 podem ser configuradas como
AGC-3 Alarm and Parameter List
DEIF A/S Page 79 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5272 Transistor 21 T21 Relay kVArh Relay
saídas relé de pulso ou sinais Se selecionada a 'Ligação' , o relé 20 e 21 estarão disponíveis. Se definido como "relé" relés externos são necessários devido à limitada produção atual. Máx. 10 mA.
Limite De Saída Analógica
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5720 PWM 68 limits
5721 PWM 68 limits Min. 0 % 50 %
10 %
5722 PWM 68 limits Max. 50 % 100%
90 %
Option: PWM output (EF5)
Para motores Caterpillar.
5780 Aout 66 limits
5781 AOut 66 limits Min. -25/0 mA 10 mA
-20/0 mA
5782 AOut 66 limits Max. 10 mA 25 mA 20 mA
Option: 2 x
analogue outputs (E1/E2)
Mínimo range e a confirguração de fábrica é opção dependente.
5790 Aout 71 limits
5791 AOut 71 limits Min. -25/0 mA 10 mA
-20/0 mA
5792 AOut 71 limits Max. 10 mA 25 mA 20 mA
Option: 2 x
analogue outputs (E1/E2)
Mínimo range e a confirguração de fábrica é opção dependente.
5800 Aout 91 limits
5801 AOut 91 limits Min. 0 mA 10 mA
0 mA
5802 AOut 91 limits Max. 10 mA 25 mA 20 mA
Option: 2 x
analogue outputs
(F1)
Mínimo range e a confirguração de fábrica é opção dependente.
5810 Aout 95 limits
5811 AOut 95 limits Min. 0 mA 10 mA
0 mA
5812 AOut 95 limits Max. 10 mA 25 mA 20 mA
Option: 2 x
analogue outputs
(F1)
Mínimo range e a confirguração de fábrica é opção dependente.
AGC-3 Alarm and Parameter List
DEIF A/S Page 80 of 112
Saída De Transdutores
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5820 P output 1
5821 P output 1 Output A R0
Option dep.
R0 (none)
5822 P output 1 Output B R0
Option dep.
R0 (none)
5823 P output 1 Type 0-20 mA 4-20 mA
4-20 mA
5824 P output 1 Max. value 0 kW 20000
kW 500 kW
5825 P output 1 Min. value -9999 kW
20000 kW
0 kW
Option : Analogue outputs
(E2 or F1 or EF2)
5830 P output 2
5831 P output 2 Output A R0
Option dep.
R0 (none)
5832 P output 2 Output B R0
Option dep.
R0 (none)
5833 P output 2 Type 0-20 mA 4-20 mA
4-20 mA
5834 P output 2 Max. value 0 kW 20000
kW 500 kW
5835 P output 2 Min. value -9999 kW
20000 kW
0 kW
Option : Analogue outputs
(E2 or F1 or EF2)
5840 P output 3
5841 P output 3 Output A R0
Option dep.
R0 (none)
5842 P output 3 Output B R0
Option dep.
R0 (none)
5843 P output 3 Type 0-20 mA 4-20 mA
4-20 mA
5844 P output 3 Max. value 0 kW 20000
kW 500 kW
5845 P output 3 Min. value -9999 kW
20000 kW
0 kW
Option : Analogue outputs
(E2 or F1 or EF2)
5850 S output
5851 S output Output A R0
Option dep.
R0 (none) Option :
Analogue outputs
AGC-3 Alarm and Parameter List
DEIF A/S Page 81 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5852 S output Output B R0
Option dep.
R0 (none)
5853 S output Type 0-20 mA 4-20 mA
4-20 mA
5854 S output Max. value 0 kVA 20000 kVA
600 kVA
5855 S output Min. value
-9999 kVA
20000 kVA
0 kVA
(E2 or F1 or EF2)
5860 Q output
5861 Q output Output A R0
Option dep.
R0 (none)
5862 Q output Output B R0
Option dep.
R0 (none)
5863 Q output Type 0-20 mA 4-20 mA
4-20 mA
5864 Q output Max. value 0 kVAr 16000 kVAr
400 kVAr
5865 Q output Min. value
-9999 kVA
20000 kVA
0 kVAr
Option : Analogue outputs
(E2 or F1 or EF2)
5870 PF output
5871 PF output Output A R0
Option dep.
R0 (none)
5872 PF output Output B R0
Option dep.
R0 (none)
5873 PF output Type 0-20 mA 4-20 mA
4-20 mA
5874 PF output Max. value 0.5 0.99
0.80
5875 PF output Min. value -0.99 -0.50
-0.80
Option : Analogue outputs
(E2 or F1 or EF2)
Valor positivo significa indutivo Valor negativo significa capacitivo
5880 f output
5881 F output Output A R0
Option dep.
R0 (none)
5882 F output Output B R0
Option dep.
R0 (none)
5883 F output Type 0-20 mA 4-20 mA
4-20 mA
5884 F output Max. value 0.0 Hz 70.0 Hz
55.0 Hz
5885 F output Min. value 0.0 Hz 70.0 Hz
45.0 Hz
Option : Analogue outputs
(E2 or F1 or EF2)
AGC-3 Alarm and Parameter List
DEIF A/S Page 82 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5890 U output
5891 U output Output A R0
Option dep.
R0 (none)
5892 U output Output B R0
Option dep.
R0 (none)
5893 U output Type 0-20 mA 4-20 mA
4-20 mA
5894 U output Max. value 0 V 28000 V
500 V
5895 U output Min. value 0 V 28000 V
0 V
Option : Analogue outputs
(E2 or F1 or EF2)
A tensão de saída representa L1-L2 tensão
5900 I output
5901 I output Output A R0
Option dep.
R0 (none)
5902 I output Output B R0
Option dep.
R0 (none)
5903 I output Type 0-20 mA 4-20 mA
4-20 mA
5904 I output Max. value 0 A 9000 A
1000 A
5905 I output Min. value 0 A 9000 A
0 A
Option : Analogue outputs
(E2 or F1 or EF2)
A saída de corrente representa L1 corrente
5910 U BB output
5911 U BB output Output A R0
Option dep.
R0 (none)
5912 U BB output Output B R0
Option dep.
R0 (none)
5913 U BB output Type 0-20 mA 4-20 mA
4-20 mA
5914 U BB output Max. value 0 V 28000 V
500 V
5915 U BB output Min. value 0 V 28000 V
0 V
Option : Analogue outputs
(E2 or F1 or EF2)
A tensão de saída representa L1-L2 tensão
5920 f BB output
5921 F BB output Output A R0
Option dep.
R0 (none)
5922 F BB output Output B R0
Option dep.
R0 (none)
5923 F BB output Type 0-20 mA 4-20 mA
4-20 mA
5924 F BB output Max. value 0.0 Hz 70.0 Hz
55.0 Hz
5925 F BB output Min. value 0.0 Hz 70.0 Hz
45.0 Hz
Option : Analogue outputs
(E2 or F1 or EF2)
5930 Multi-input 102
AGC-3 Alarm and Parameter List
DEIF A/S Page 83 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5931 Multi-input 102 Output A R0
Option dep.
R0 (none)
5932 Multi-input 102 Output B R0
Option dep.
R0 (none)
5933 Multi-input 102 Type 0-20 mA 4-20 mA
4-20 mA
5934 Multi-input 102 Max. value 0 28000
500
5935 Multi-input 102 Min. value 0 28000
0
Option : Analogue outputs
(E2 or F1 or EF2)
5940 Multi-input 105
5941 Multi-input 105 Output A R0
Option dep.
R0 (none)
5942 Multi-input 105 Output B R0
Option dep.
R0 (none)
5943 Multi-input 105 Type 0-20 mA 4-20 mA
4-20 mA
5944 Multi-input 105 Max. value 0 28000
500
5945 Multi-input 105 Min. value 0 28000
0
Option : Analogue outputs
(E2 or F1 or EF2)
5950 Multi-input 108
5951 Multi-input 108 Output A R0
Option dep.
R0 (none)
5952 Multi-input 108 Output B R0
Option dep.
R0 (none)
5953 Multi-input 108 Type 0-20 mA 4-20 mA
4-20 mA
5954 Multi-input 108 Max. value 0 28000
500
5955 Multi-input 108 Min. value 0 28000
0
Option : Analogue outputs
(E2 or F1 or EF2)
.
5960 P total consumed
5961 P total consumed Output A R0
Option dep.
R0 (none)
5962 P total consumed Output B R0
Option dep.
R0 (none)
5963 P total consumed Type 0-20 mA 4-20 mA
4-20 mA
5964 P total consumed Max. value 0 kW 20000
kW 500 kW
5965 P total consumed Min. value -9999 kW
20000 kW
0 kW
Option : Analogue outputs
(E2 or F1 or EF2)
5970 P total available
AGC-3 Alarm and Parameter List
DEIF A/S Page 84 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
5971 P total available Output A R0
Option dep.
R0 (none)
5972 P total available Output B R0
Option dep.
R0 (none)
5973 P total available Type 0-20 mA 4-20 mA
4-20 mA
5974 P total available Max. value 0 kW 20000
kW 500 kW
5975 P total available Min. value -9999 kW
20000 kW
0 kW
Option : Analogue outputs
(E2 or F1 or EF2)
Seleção Do Regulador De Saída
No. Setting Available settings
Factory setting
Notes Ref. Description
5980 Governor output
5981 Governor output Output A Disabled
AO66 AO71
Disabled
Option: Analogue governor
output (E1/EF)
5990 AVR output
5991 AVR output Output A Disabled
AO66 AO71
Disabled
Option: Analogue
AVR output (E1/EF and D1)
Sistema
These menus are used to select which analogue output to use for governor/AVR (option D) control.
These menus includes parameters for the system setup
AGC-3 Alarm and Parameter List
DEIF A/S Page 85 of 112
Programação Geral
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6000 Nominal settings 1
6001 Nom. settings Frequency 48.0 Hz 62.0 Hz
50.0 Hz
6002 Nom. settings Power 10 kW 20000 kW
480 kW
6003 Nom. settings Current 0 A 9000 A
867 A
6004 Nom. settings Voltage 100 V 25000 V
400 V
6005 Nom. settings RPM 100 RPM 4000 RPM
1500 RPM
6006 Nom. settings Set 1 4
1
Designers Reference Handbook
A seleção de definições nominais a ser utilizada é fixada em 6006. 1 entrada binária ou de seleção no M-Logic também pode ser utilizado.
6010 Nominal settings 2
6011 Nom. Settings 2 Frequency 48.0 Hz 62.0 Hz
50.0 Hz
6012 Nom. Settings 2 Power 10 kW 20000 kW
230 kW
6013 Nom. Settings 2 Current 0 A 9000 A
345 A
6014 Nom. Settings 2 Voltage 100 V 25000 V
480 V
6015 Nom. Settings 2 RPM 100 RPM 4000 RPM
1500 RPM
Designers Reference Handbook
6020 Nominal settings 3
6021 Nom. Settings 3 Frequency 48.0 Hz 62.0 Hz
60.0 Hz
6022 Nom. Settings 3 Power 10 kW 20000 kW
230 kW
6023 Nom. Settings 3 Current 0 A 9000 A
345 A
6024 Nom. Settings 3 Voltage 100 V 25000 V
480 V
6025 Nom. Settings 3 RPM 100 RPM 4000 RPM
1800 RPM
Designers Reference Handbook
6010 Nominal settings 4
6031 Nom. Settings 4 Frequency 48.0 Hz 62.0 Hz
60.0 Hz
6032 Nom. Settings 4 Power 10 kW 20000 kW
230 kW
6033 Nom. Settings 4 Current 0 A 9000 A
345 A
6034 Nom. Settings 4 Voltage 100 V 25000 V
480 V
6035 Nom. Settings 4 RPM 100 RPM 4000 RPM
1800 RPM
Designers Reference Handbook
AGC-3 Alarm and Parameter List
DEIF A/S Page 86 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6040 Gen/Mains/busbar A transformer
6041 G/M/BA transformer
U primary 100 V 25000 V
400 V
6042 G/M/BA transformer
U secondary
100 V 690 V
400 V
6043 G/M/BA transformer
I primary 5 A 9000 A
1000 A
6044 G/M/BA transformer
I secondary 1 A 5 A
5 A
Designers Reference Handbook
Se nenhum transformador de tensão estiver presente, os valores do primário e secundário serão estabelecidos pelo valor nominal do gerador.
6050 Busbar transformer
6041 BB transformer U primary 100 V 25000 V
400 V
6042 BB transformer U secondary
100 V 690 V 400 V
Designers Reference Handbook
Se nenhum transformador de tensão estiver presente, os valores do primário e secundário serão estabelecidos pelo valor nominal do gerador.
6070 Gen-set Mode
6071 Gen-set mode Island Power management
Designers Reference Handbook
Possibilidade de seleções: -Island -Auto Mains Failure -Peak Shaving -Fixed power -Mains power export -Load take over -Power management (option G5)
6080 Language
6081 Language English Language 1-11
English
Designers Reference Handbook
O idioma master é o Inglês. Além disso 11 línguas diferentes pode ser configurado com o PC utility software.
Contadores e Relógios
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6100 Counters
6101 Counters Running hour
0 hr 999 hr
0 hr
6102 Counters Running, th. Hours
0 th. hrs 99 th. hrs
0 th. hrs
6103 Counters GB/TB/BTB operations
0 20000
0
6104 Counters MB operations
0 20000
0
Designers Reference Handbook
Parâmetro 6105 reseta o kWh para 0. Ele retorna automaticamente para OFF depois de ser resetado no dia.
AGC-3 Alarm and Parameter List
DEIF A/S Page 87 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6105 Counters kWh OFF ON
OFF
6106 Counters Start attempts
0 20000
0
6110 Service timer 1
6111 Service timer 1 Enable OFF ON
ON
6112 Service timer 1 Running hours
0 hrs 9000 hrs
500 hrs
6113 Service timer 1 Days 1 days 1000 days
365 days
6114 Service timer 1 Fail class F1…F8 F2 (warning)
6115 Service timer 1 Output A Not used Option
dependent Not used
6116 Service timer 1 Reset OFF ON
OFF
Designers Reference Handbook
O temporizador é reiniciado, permitido pelo menu 6116. O menu vai automaticamente para OFF.
6120 Service timer 2
6121 Service timer 2 Enable OFF ON
ON
6122 Service timer 2 Running hours
0 hrs 9000 hrs
500 hrs
6123 Service timer 2 Days 1 days 1000 days
365 days
6124 Service timer 2 Fail class F1…F8 F2 (warning)
6125 Service timer 2 Relay output A
Not used Option
dependent Not used
6126 Service timer 2 Reset OFF ON
OFF
Designers Reference Handbook
O temporizador é reiniciado, permitido pelo menu 6126. O menu vai automaticamente para OFF.
Alarme Cirene
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6130 Alarm horn
6131 Alarm horn ON time 0.0 sec 990.0 sec 0.0 sec
Designers Reference Handbook
Se a configuração está ajustado para 0 s, o relé da cirene será ativado continuamente até que o alarme seja reconhecido.
AGC-3 Alarm and Parameter List
DEIF A/S Page 88 of 112
Funcionamento, Partida e Parada
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6160 Run status
6161 Run status Delay 0.0 sec 300.0 sec
5.0 sec
6162 Run status Relay
output A Not used Option
dependent Not used
6163 Run status Relay
output B Not used Option
dependent Not used
6164 Run status Enable OFF ON
OFF
Designers Reference Handbook
Se um relé de saída é utilizado, o relé em questão deve ser definido como 'limite'.
6170 Running detection
6171 Running detect. No of Teeth 0 teeth 500 teeth
0 teeth
6172 Running detect. Type Digital in Multi-input
Frequency
6173 Running detect. Running RPM
0 RPM 4000 RPM
1000 RPM
6174 Running detect. Remove starter
1 RPM 2000 RPM
400 RPM
6175 Running detect. Pressure level
0.0 bar 15.0 bar
0.0 bar
Designers Reference Handbook
Se menu 6171 está definido para 0,a entrada do pickup magnetic não está activa. Tipos de detectores de status de funcionamento: - Entrada digital - Pickup magnetico - Frequência - EIC (Comunicação
motor) - Multi-input (Presão
óleo) Se menu 6175 está definido para 0.0, o status de funcionamento por presão de óleo fica OFF.
6180 Starter
6181 Starter Start prepare
0.0 sec 600.0 sec
5.0 sec
6182 Starter Ext. prepare 0.0 sec 600.0 sec
0.0 sec
6183 Starter Start ON time
1.0 sec 180.0 sec
5.0 sec
6184 Starter Start OFF time
1.0 sec 99.0 sec
5.0 sec
6185 Starter Input type
Multi-input 102
Multi-input 108
Multi-input 102
6186 Starter Setpoint 0.0 bar 300.0 bar
0.0 bar
Designers Reference Handbook
Menu 6185 e 6186 diz respeito à utilização do pressão do óleo como feedback de funcionamenoto. Se menu 6186 está definido para 0.0, o feedback de funcionamento por pressão do óleo, é ignorado.
6190 Start attempts
AGC-3 Alarm and Parameter List
DEIF A/S Page 89 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6181 Start attempts Setpoint 1 10 3
Designers Reference Handbook
Números de tentativas de partidas
6200 Shutdown override
6201 Shutdown override
Attempts 1 10
7
6202 Shutdown override
Cooling down
0.0 sec 9900.0 sec
240.0 sec
6203 Shutdown override
Enable OFF ON
OFF
Designers Reference Handbook
Shutdown override transforma todas as paradas programadas alarmes. Única exceção é o overspeed e parada de emergência.
6210 STOP
6211 STOP Cooling down
1.0 sec 9900.0 sec
240.0 sec
6212 STOP Extended stop
2.0 sec 99.0 sec 5.0 sec
Designers Reference Handbook
O tempo do extended stop começa a correr quando feedback desaparece. Durante o tempo de atraso não é possível iniciar o motor.
6220 Hz/V OK
6221 HZ/V OK Delay 1.0 sec 99.0 sec 5.0 sec
Designers Reference Handbook
A tensão e a frequência tem de ser continuamente dentro dos limites antes que o disjuntor pode ser fechado.
Controle Do Disjuntor
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6230 Gen/Mains/Tie/Bus tie Breaker control
6211 GB/MB/TB/BTB control
Close delay 0.0 sec 30.0 sec
2.0 sec
6212 GB/MB/TB/BTB control
Load time 0.0 sec 30.0 sec
0.0 sec
Designers Reference Handbook
Menu 6212 é para disjuntores compactos (necessidade de carregar a mola antes de fechar).
Taxa De Decremento
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6260 Power derate
6261 Power derate Input Multi in 102 MLogic
Multi in 102
6262 Power derate Start derate 0 units 20000 units
16 units
Designers Reference Handbook
A função derate é para baixar a potência máxima do gerador baseado em conjunto,
AGC-3 Alarm and Parameter List
DEIF A/S Page 90 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6263 Power derate Derate slope
0.1 %/unit 100.0 %/unit
5.0 %/unit
6264 Power derate Proportional OFF ON
OFF
6265 Power derate Enable OFF ON
OFF
6266 Power derate Limit 0.0 % 100.0 %
80.0 %
por exemplo a temperatura da água.
Partida em Marcha Lenta
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6290 Idle start
6291 Idle start Start Timer 0.0 min 999.0 min
300.0 min
6292 Idle start Enable start OFF ON
OFF
6293 Idle start Stop timer 1.0 min 999.0 min
6294 Idle start Enable stop OFF ON
OFF
6295 Idle start Output A Not used Option dep.
Not used
6296 Idle start Enable OFF ON
OFF
Designers Reference Handbook
Aquecimento Do Motor
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6320 Engine heater
6321 Engine heater Setpoint 20 deg 250 deg
40 deg
6322 Engine heater Output A Not used Option dep
Not used
6323 Engine heater Type Multi inp 102 Multi inp. 108
Multi inp 102
6324 Engine heater Hysteresis 1 deg 70 deg
3 deg
6325 Engine heater Enable OFF ON
OFF
Designers Reference Handbook
Função de parade do aquecedor
Linhas De Saída Do Divisor De Carga Analógico
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
AGC-3 Alarm and Parameter List
DEIF A/S Page 91 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6380 Loadshare out
6381 Loadshare out Setpoint 1 V 5 V
4 V
Option G3 Analogue load sharing
Ajuste da linha de load sharing analógico valor máximo
6390 Loadshare type
6391 Loadshare type Setpoint Adjustable
Selco T4800
Option G3 Analogue load sharing
Seleção entre linha de load sharing selecionável, valor máximo (parâmetro 6381) ou a adaptação a Selco T4800 linha de load sharing.
Temporizador
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6400 Master clock
6401 Master clock Start hour 0 h 23 h
8 h
6402 Master clock Stop hour 0 h 23 h
8 h
6403 Master clock Difference 1 sec 999 sec
20 sec
6404 Master clock Compen-sation
0.1 Hz 1.0 Hz
0.1 Hz
6405 Master clock Enable OFF ON
OFF
Designers Reference Handbook
Compensação de variação relacionada com freqüência e o tempo no sistema.
Ventilador De Resfriamento
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6460 Max. ventilation
6461 Max ventilation Setpoint 20 deg 250 deg
90 deg
6462 Max ventilation Output A Not used Option dep
Not used
6463 Max ventilation Hysteresis 1 deg 70 deg
5 deg
6464 Max ventilation Enable OFF ON
OFF
Designers Reference Handbook
Partir/Parar Próximo Gerador
AGC-3 Alarm and Parameter List
DEIF A/S Page 92 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6520 Start next gen
6521 Start next gen Setpoint 0 % 100 %
20 %
6522 Start next gen Timer 0.0 sec 200.0 sec
30.0 sec
6523 Start next gen Output A Not used Option dep
Not used
6524 Start next gen Output B Not used Option dep
Not used
6525 Start next gen Enable OFF ON
OFF
Option G1 Sinal de partida para o próxima gerador. Programe o relé selecionado para o modo "Limite".
6530 Stop next gen
6531 Stop next gen Setpoint 50 % 100 %
80 %
6532 Stop next gen Timer 1.0 sec 100.0 sec
10.0 sec
6533 Stop next gen Output A Not used Option dep
Not used
6534 Stop next gen Output B Not used Option dep
Not used
6535 Stop next gen Enable OFF ON
OFF
Option G1 Sinal de parada para o próxima gerador. Programe o relé selecionado para o modo "Limite".
Bomba De Combustível
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6550 Fuel pump logic
6291 Fuel Pump Logic Setpoint start
0 % 100 %
20 %
6292 Fuel Pump Logic Setpoint stop
0 % 100 %
80 %
6293 Fuel Pump Logic Fill check time
0.1 sec 300.0 sec
60.0 sec
6294 Fuel Pump Logic Output A Not used Option dep.
Not used
6295 Fuel Pump Logic Type Multi in 102 Multi in 108
Multi in 102
6296 Fuel Pump Logic Failclass F1…F7 Warning (F2)
Designers Reference Handbook
Horário De Verão
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6490 Summer/winter time
AGC-3 Alarm and Parameter List
DEIF A/S Page 93 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
6491 Sum/Win time Enable OFF ON OFF
Designers Reference Handbook
O verão / inverno mudança tempo segue regras do continente europeu.
Programar Rede
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7000 Mains power
7001 Mains power Day -20000 kW 20000 kW
750 kW
7002 Mains power Night -20000 kW 20000 kW
1000 kW
7003 Mains power Transducer max
0 kW 20000 kW
0 kW
7004 Mains power Transducer min
-20000 kW 0 kW
0 kW
Designers Reference Handbook
7010 Daytime period
7011 Daytime period Start hour 0 h 23 h
8 h
7012 Daytime period Start minute 0 min 59 min
0 min
7013 Daytime period Stop hour 0 h 23 h
16 h
7014 Daytime period Stop period 0 min 59 min
0 min
Designers Reference Handbook
O período fora do período diurno é definido como o período noturno.
7020 Start generator
7021 Start generator Setpoint 5% 100%
80%
7022 Start generator Delay 0.0 s 990.0 s
10.0 s
7023 Start generator Minimum load
0% 100%
5%
Designers Reference Handbook
O setpoint refere ao menu 7000 do mains, setting de potência.
7030 Stop generator
7031 Stop generator Setpoint 5% 80%
60%
7032 Stop generator Delay 1.0 s 990.0 s
30.0 s
Designers Reference Handbook
O setpoint refere ao menu 7000 do mains, setting de potência.
Teste
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7040 Test running
AGC-3 Alarm and Parameter List
DEIF A/S Page 94 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7041 Test Setpoint 1% 100%
80%
7042 Test Test time 0.5 min 999.0 min
5.0 min
7043 Test Return mode Semi- auto Auto
Auto
7044 Test Test type Simple Full
Simple
Designers Reference Handbook
Tipos de testes disponiveis: - Simples (motor
funcionando apenas) - Carga (paralelo com a
rede) - combústivel
(disconectado da rede)
Controle De Configuração
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7050 Controller settings
7051 Controller settings Power 0 % 100 %
100 %
7052 Controller settings Power factor 0.6 1.0
0.9
7053 Controller settings Power factor Inductive Capacitive
Inductive
Designers Reference Handbook
Definições de paralelo com a rede.
Falha De Rede
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7060 U Mains Failure
AGC-3 Alarm and Parameter List
DEIF A/S Page 95 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7061 U Mains failure
Fail. delay
0.0 sec 990.0 sec
5.0 sec
Designers Reference Handbook
- Menus
7063 e 7064 refere-se a definições nominais. Menu 7066 refere-se ao valor médio da medida de tensão.
7062 U Mains failure
MSB OK delay
10 sec 9900 sec
60 sec
7063 U Mains failure
U< 80% 100% 90%
7064 U Mains failure
U> 100% 120% 110%
7065 U Mains failure
MSB fail. control
Start eng. +
open TB Start eng.
Start eng. + open TB
7066 U Mains failure
Unbalance U
2% 100% 100%
7070 f Mains Failure
7071 f Mains failure
Fail. delay 1.0 sec
990.0 sec
5.0 sec
7072 f Mains failure
MSB OK delay
10 sec 9900 sec
60 sec
7073 f Mains failure
f< 80.0% 100% 95%
7074 f Mains failure
f> 100% 120% 105%
Designers Reference Handbook
Menus 7073 e 7074 refere-se a definições nominais.
-
7080 MB control
AGC-3 Alarm and Parameter List
DEIF A/S Page 96 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7081 MB control
Mode Shift
OFF ON OFF
7082 MB control
MB close delay
0.0 sec
30.0 sec 0.5 sec
7083 MB control
Back sync.
OFF ON OFF
7084 MB control
Sync to Mains
OFF ON ON
7085 MB control
Load time 0.0 se
c 30.0 sec
0.0 sec
Designers Reference Handbook
Modo De Falha CAN
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7130 CAN fail mode
7132 CAN fail mode
Setpoint
Manual No mode change
Manual
Seleções disponíveis: Manual Semi-auto Não há nenhum modo mudança
Comunicação Externa
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7500 Communication control
7501 Comm. control Power OFF ON
OFF
7502 Comm. control Frequency OFF ON
OFF
7503 Comm. control Voltage OFF ON
OFF
7504 Comm. control PF OFF ON
OFF
7505 Comm. control Reactive power
OFF ON
OFF
Option: Modbus (H2) or
Profibus (H3)
Estas definições devem ser ON quando o comando é enviado através da comunicação Modbus. Isto irá ignorar configurações externa e interna. Controle tensão, fator de potência e potência reativa requer controle AVR (opção D1).
7510 External communication
7511 Ext. communication ID
1 247 1
Option: Modbus (H2) or
Profibus (H3)
O modo ASCII é utilizado para comunicação com modem (ASCII: 7 bits de dados, RTU: 8 bits
AGC-3 Alarm and Parameter List
DEIF A/S Page 97 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7512 Ext. communication Baud rate
9600 19200 9600
Option: Modbus
(H2)
7513 Ext. communication Mode
RTU ASCII RTU
Option: Modbus
(H2)
de dados)
AGC-3 Alarm and Parameter List
DEIF A/S Page 98 of 112
Comunicação Interna Do Power Management
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7530 Internal communication ID
7531 Int. comm. ID
ID
1 16 1
Designers Reference Handbook
Comunicação De Interface Do Motor
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7560 Engine I/F
7561 Engine I/F Engine
type
OFF QSX15 QSK23/45/60/78 QST30
OFF
Option: Cummins Modbus
(H6)
O parâmetro afeta os dados exibidos, mas não os dados Modbus (opção H2).
7561 Engine I/F Engine
type
OFF DDEC EMR JDEC Iveco Perkins Caterpillar Volvo Penta EMS Volvo Penta EMS 2 Scania EMS Scania EMS S6 MDEC 2000/4000 M.302 MDEC 2000/4000 M.303 MTU ADEC Cummins Generic J1939
OFF
7562 CANopen ID Node ID
1
128 6
7563 EIC Controls Enable
On
Off On
7564 EIC Auto view
Enable On
Off Off
Option: J1939/MTU
ADEC/ MTU
MDEC (H5)
J1939 (H7)
MTU MDEC só está disponível na opção H5 Por favor, escolha MDEC 2000/4000 M.303, M.201 ou M.304 quando é necessário. Menu 7562 só está disponível quando MTU ADEC é selecionado como tipo de motor. Menu 7563 é para permitir a transmissão comandos EIC Menu 7564: quando configurado para "on" até 19 visualizações extras (de 3 linhas) são adicionados ao V1 15 visualizações originais (de 3 linhas). Estas visualizações são exibidas no display com valores difundidas do motor sobre este comunicação CAN quando esta função está definida no "on".
AGC-3 Alarm and Parameter List
DEIF A/S Page 99 of 112
Programar Comunicação De I/O Externo
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7950 KL320x config
7951 KL320x config Module 1
7952 KL320x config Module 2
7953 KL320x config Module 3
7954 KL320x config Module 4 Pt100 (2/3-wire) 10- 1200 � (2-wire)
Option: External I/O
modules (H8)
Seleção para módulos Analógicos. As seleções da KL 3202/3204 não pode ser alterado. Após alterar tipo módulo, a lista de parâmetros no USW PC deve ser carregado novamente.
7970 CAN 1
7971 CAN 1 Type OFF AOP-2 Beckhoff
OFF
7972 CAN 1 Baud 50k 125k 250k
125k
7973 CAN 1 ID 1 to 64
1
7974 CAN 1 Reset
NO YES
NO
Option: External I/O
modules (H8)
Este menu só é ativado se a opção H8.6 estiver ativada. Após alterar tipo módulo, a lista de parâmetros no USW PC deve ser carregado novamente. Menu 7974 é para restabelecer a comunicação depois de uma falha / desconexão
7980 CAN 2
7981 CAN 2 Type OFF AOP-2 Beckhoff
OFF
7982 CAN 2 Baud 50k 125k 250k
125k
7983 CAN 2 ID 1 to 64
1
7984 CAN 2 Reset
NO YES
NO
Option: External I/O
modules (H8)
Este menu só é ativado se a opção H8.8 está activada. Após alterar tipo módulo, a lista de parâmetros no USW PC deve ser carregado novamente. Menu 7984 é para restabelecer a comunicação depois de uma falha / desconexão
Imprimir Eventos
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7990 Event printer
7991 Event printer Enable OFF ON
OFF Tipos de logs: Evento
AGC-3 Alarm and Parameter List
DEIF A/S Page 100 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
7992 Event printer Print add data OFF ON
OFF
7993 Event printer Event records 1 150
5
7994 Event printer Log type select
Event Battery
Event
7995 Event printer Auto status 0 min 990 min
0 min
Alarme Bateria Se status auto for definido como 0, a impressão é automáticamente desabilitada
Programar Gerenciador De Potência
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
8000 Load dependent start
8001 Load dep. Start Setpoint 0 kW 20000 kW
100 kW
8002 Load dep. Start Delay 0.0 sec 990.0 sec
10.0 sec
8003 Load dep. Start Min. load 0 kW 20000 kW
20 kW
Designers Reference Handbook
8010 Load dependent stop
8011 Load dep. Stop Setpoint 0 kW 20000 kW
180 kW
8012 Load dep. Stop Delay 0.0 sec 990.0 sec
30.0 sec
Designers Reference Handbook
8030 Priority selection
8031 Priority select. Priority Manual
Fuel optimise
Manual
8032 Priority select. No. multi-start 1 16
1
8033 Priority select. Min. no. running
1 16
1
8034 Priority select. Enable multi-start
OFF ON
OFF
Designers Reference Handbook
Prioridades disponíveis: - Manual - Horas funcionamento - Optimização
combustível
8080 Priority (1-5)
8081 Priority 1 ID 1 16
1
8082 Priority 2 ID 1 16
2
8083 Priority 3 ID 1 16
3
8084 Priority 4 ID 1 16
4
8085 Priority 5 ID 1 16
5
8086 Transmit new priority
Tx ON OFF
OFF
Designers Reference Handbook
Menu 8086 está disponível apenas se o "Manual" está selecionado no menu 8031. Menu 8086 repõe-se a desligar automaticamente uma vez que as novas configurações tenham sido transmitidos.
AGC-3 Alarm and Parameter List
DEIF A/S Page 101 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
8090 Priority (6-11)
8091 Priority 6 ID 1 16
6
8092 Priority 7 ID 1 16
7
8093 Priority 8 ID 1 16
8
8094 Priority 9 ID 1 16
9
8095 Priority 10 ID 1 16
10
8096 Priority 11 ID 1 16
11
Designers Reference Handbook
8100 Priority (12-16)
8101 Priority 12 ID 1 16
12
8102 Priority 13 ID 1 16
13
8103 Priority 14 ID 1 16
14
8104 Priority 15 ID 1 16
15
8105 Priority 16 ID 1 16
16
Designers Reference Handbook
8110 Running hours
8111 Running hours Set timer 1 hrs 20000 hrs
175 hrs
8112 Running hours Type Absolute Relative
Absolute
8113 Running hours Reset OFF ON
Designers Reference Handbook
8120 Ground relay
8121 Ground relay Output A Not used Option dep.
Not used
8122 Ground relay Output B Not used
Option dep.
Not used
8123 Ground relay Enable Off On
Off
Designers Reference Handbook
8140 Stop non-connected DGs
8141
Stop non-con. DGs Delay
2.0 sec 600.0 sec 60.0 sec
Option: Power
manage-ment (G5)
8170 Fuel Optimize
8171 Fuel optimize Setpoint 30% 100%
80% Option: Power
AGC-3 Alarm and Parameter List
DEIF A/S Page 102 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
8172 Fuel optimize Swap setpoint 50 kW 20000 kW
200 kW
8173 Fuel optimize Delay 0.0 sec 999.0 sec
10.0 sec
8174 Fuel optimize Hours 1 hrs 20000 hrs
175 hrs
8175 Fuel optimize Enable hour OFF ON
OFF
manage-ment (G5)
8180 Mains config.
8181 Mb failure start Enable OFF ON
OFF
8182 Parallel Enable OFF ON
OFF
8183 No break transfer Enable OFF ON
OFF
8184 Auto switch Select OFF
All sections
OFF
8185
Run type Select Run all mains
Run one mains
Run one mains
8186 Run type ID to run 17 32
17
Option: Power
manage-ment (G5)
Disponível apenas no AGC Mains: Seleção de Auto switch: -OFF -Seleção estática -Seleção dinâmica -Todas as seleções
8190 Tie breaker
8171 Tie Breaker TB open point 0 kW 20000 kW
50 kW
8172 Tie Breaker Power Capacity
1 kW 20000 kW
50 kW
8173 Tie Breaker P. cap. Overrule
5.0 s 999.9 s
30.0 s
8174 Tie Breaker P cap. Overrule
OFF ON
OFF
8175 Tie Breaker Load time 0.0 s 30.0 s
0.0 s
Option: Power
manage-ment (G5)
Disponível apenas no AGC Mains
8220 Available power 1
8221 Avail. Power 1 Setpoint 30% 100%
80%
8222 Avail. Power 1 Delay 1.0 sec 999.0 sec
10.0 sec
8223 Avail. Power 1 Output A
Not Used
Option Dependent
Not used
8224 Avail. Power 1 Output B
Not Used
Option Dependent
Not used
8225 Avail. Power 1 Enable OFF ON
OFF
Option: Power
manage-ment (G5)
O parâmetro pode ser utilizado para a ligação condicional da carga de grupos. O relé (s) utilizado deve ser definido como modo "Limite".
8230 Available power 2
AGC-3 Alarm and Parameter List
DEIF A/S Page 103 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
8231 Avail. Power 2 Setpoint 30% 100%
80%
8232 Avail. Power 2 Delay 2.0 sec 999.0 sec
10.0 sec
8233 Avail. Power 2 Output A
Not Used
Option Dependent
Not used
8234 Avail. Power 2 Output B
Not Used
Option Dependent
Not used
8235 Avail. Power 2 Enable OFF ON
OFF
Option: Power
manage-ment (G5)
O parâmetro pode ser utilizado para a ligação condicional da carga dos grupos. O relé (s) utilizado deve ser definido como modo "Limite".
8240 Available power 3
8241 Avail. Power 3 Setpoint 30% 100%
80%
8242 Avail. Power 3 Delay 3.0 sec 999.0 sec
10.0 sec
8243 Avail. Power 3 Output A
Not Used
Option Dependent
Not used
8244 Avail. Power 3 Output B
Not Used
Option Dependent
Not used
8245 Avail. Power 3 Enable OFF ON
OFF
Option: Power
manage-ment (G5)
O parâmetro pode ser utilizado para a ligação condicional da carga dos grupos. O relé (s) utilizado deve ser definido como modo "Limite".
8250 Available power 4
8251 Avail. Power 4 Setpoint 30% 100%
80%
8252 Avail. Power 4 Delay 4.0 sec 999.0 sec
10.0 sec
8253 Avail. Power 4 Output A
Not Used
Option Dependent
Not used
8254 Avail. Power 4 Output B
Not Used
Option Dependent
Not used
8255 Avail. Power 4 Enable OFF ON
OFF
Option: Power
manage-ment (G5)
O parâmetro pode ser utilizado para a ligação condicional da carga dos grupos. O relé (s) utilizado deve ser definido como modo "Limite". .
8260 Available power 5
8261 Avail. Power 5 Setpoint 30% 100%
80%
8262 Avail. Power 5 Delay 5.0 sec 999.0 sec
10.0 sec
8263 Avail. Power 5 Output A
Not Used
Option Dependent
Not used
Option: Power
manage-ment (G5)
O parâmetro pode ser utilizado para a ligação condicional da carga dos grupos. O relé (s) utilizado deve ser definido como modo "Limite". .
AGC-3 Alarm and Parameter List
DEIF A/S Page 104 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
8264 Avail. Power 5 Output B
Not Used
Option Dependent
Not used
8265 Avail. Power 5 Enable OFF ON
OFF
8270 TB Power
8271 TB Power Transducer max.
0 kW 20000 kW
0 kW
8272 TB Power Transducer min.
-20000 kW 0 kW
0 kW
Option: Power
manage-ment (G5)
Apenas alimentação AGC: Se o TB devolver a carga antes da abertura, um transdutor deve ser ligado a entrada multi-105.
AGC-3 Alarm and Parameter List
DEIF A/S Page 105 of 112
Jump menus Uma série de menus só pode ser inscrito com o salto menu:
9000 Versão de Software Informações sobre o real software transferido para a unidade. Por favor, verifique antes de contactar este serviço e apoio em matéria ás questóes com a DEIF.
9010 Mostrar caráter teste
Mostra um teste de impressão do conjunto de caracteres no visor.
9020 Porta De Serviço A porta de serviço pode ser configurada para usar a comunicação ASCII. A comunicação ASCII é utilizada quando o utility software é conectado através de um modem.
9070 M4 SW version Informações sobre a versão do software do motor I/F PCB placed in slot #8.
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
9100 Application
9100 Application Application G Unit BTB unit
G unit
Designers Reference Handbook
Este parâmetro só é acessível através do "JUMP 'botão do visor. Seleções disponíveis:
G unit (Gerador Diesel) SG unit (Gerador Eixo) SC unit (Conexão c/ Terra) EG unit (Gerador de emergencia)
BTB unit (Bus tie breaker)
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
911x Password
9116 User password Setting 0 32000
2000
9117 Service password YYYYY setting 0 32000
2001
9118 Master password XXXXX setting 0 32000
2002
Designers Reference Handbook
Recomenda-se a alterar o nível da senha do usuário , senha de serviços e de mestre, o acesso às configurações de parâmetros devem ser restringidas.
Selecione ‘0’ deve ser utilizado para ligação por cabo entre o AGC e o PC. Selecione ‘1’ deve ser usado para conecção com o modem entre o AGC e o PC.
Warning: O aparelho irá retornar para definições de fábrica, se o parâmetro for alterado!
AGC-3 Alarm and Parameter List
DEIF A/S Page 106 of 112
9120 Menu De Serviço O menu de serviço só pode ser inscrito através do "JUMP" push-button. Este menu é utilizado em situações de serviço Na selecção alarme você pode ver todos os alarmes e os seus temporizadores tempo restante se eles estão contando. A seleção de entradas e saídas mostram o estado atual das entradas e saídas. Exemplo: Modo de entradas, saídas relé e linhas de divisão de carga.
No. Setting Description
912x Service menu
9126 Service menu Timers Motra o delay do tempo do alarme
9127 Service menu Digital inputs Mostra o estado da entrada digital
Service menu Digital outputs Mostra o estado da saída digital
9128 Service menu Miscellaneous Mostra informações mist.
9130 AC config. Este menu é utilizado para escolher entre os diferentes sistemas de medição de AC.
No. Setting Description
9130 AC config
9130 AC config Setting 3 phase L1L2L3 (1)
No. Setting Description
9150 Backlight dim
9150 Backlight dim Ajusta a intensidade da luz para o visor.
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
9160 User defined application
9160 Application Appl 1 (1) Appl 4 (4)
Appl. 1 (1)
Designers Reference Handbook
As 4 diferentes aplicações disponíveis tornam possível a passagem entre os diferentes tipos de plantas.
AGC-3 Alarm and Parameter List
DEIF A/S Page 107 of 112
Comandos De Horário
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
10000 Start/stop command 1
10001 Start/stop cmd. 1 Setpoint Start Stop
Start
10002 Start/stop cmd. 1 Enable ON OFF
OFF
Designers reference handbook
10010 Cmd. 1 day(s)
10011 Cmd. 1 days Setpoint
MO MO-TU-WE-TH-FR-SA-
SU
MO-TU-WE-TH-FR-SA-
SU
Designers reference handbook
Seleções possíveis: MO TU WE TH FR SA SU MO-TU-WE-TH MO-TU-WE-TH-FR SA-SU MO-TU-WE-TH-FR-SA-SU
10020 Cmd. 1 hour
10021 Cmd. 1 hour Setpoint 0
23 10 Designers
reference handbook
10030 Cmd. 1 min
10031 Cmd. 1 min Setpoint 0
59 0 Designers
reference handbook
Há 8 idênticos temporizadores no comando da unidade, mas apenas o comando temporizador 1 é mostrado aqui. Os comandos temporizadores só podem ser acessados com o PC Utility Software ver. 3
AGC-3 Alarm and Parameter List
DEIF A/S Page 108 of 112
Configuração GSM
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
10320 GSM Pin code
GSM Pin code Function
0 9999 1933
Designers Reference Handbook
10330 Telephone no. 1
10330 Telephone 1 Function 0
99999999999 12345678903
Designers Reference Handbook
Senhas
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
10390 Password Language page
10390 Passw. Lang. page None Customer
None
Designers Reference Handbook
As seleções estão : - None - Master - Service - Customer
10400 Password Log page
10400 Passw. Log page None Customer
None
Designers Reference Handbook
As seleções estão : - None - Master - Service - Customer
10410 Password Control page
10410 Passw. Control page None Customer
None
Designers Reference Handbook
As seleções estão : - None - Master - Service - Customer
GSM configurações só estão disponíveis no Utility Software
Telephone no.’s 2-5 settings 10340-10370 equal to setting 10330
Senha configurações só estão acessíveis no Utility Software
AGC-3 Alarm and Parameter List
DEIF A/S Page 109 of 112
VDO 102
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
10460 VDO 1 type
10460 VDO 1 type Sensor type 1 Configurable
Sensor type 1
Designers Reference Handbook
Selections are: -Sensor type 1 -Sensor type 2 -Sensor type 3 -Configurável
10470 VDO 1 Input setpoint 1
10470 VDO 1 inp. Setp. 1 0 Ohm
480 Ohm 10 Ohm
Designers Reference Handbook
Curva da VDO configurável
10480 VDO 1 Output setpoint 1
10480 VDO 1 outp. Setp. 1 -49 482 40
Designers Reference Handbook
Curva da VDO configurável
10490 VDO 1 Input setpoint 2
10480 VDO 1 inp. Setp. 2 0 Ohm
480 Ohm 44.9 Ohm
Designers Reference Handbook
Curva da VDO configurável
10500 VDO 1 Output setpoint 2
10500 VDO 1 outp. Setp. 2 -49 482 50
Designers Reference Handbook
Curva da VDO configurável
10510 VDO 1 Input setpoint 3
10510 VDO 1 inp. Setp. 3 0 Ohm
480 Ohm 81 Ohm
Designers Reference Handbook
Curva da VDO configurável
10520 VDO 1 Output setpoint 3
10520 VDO 1 outp. Setp. 3 -49 482 60
Designers Reference Handbook
Curva da VDO configurável
10530 VDO 1 Input setpoint 4
10530 VDO 1 inp. Setp. 4 0 Ohm
480 Ohm 134,7 Ohm
Designers Reference Handbook
Curva da VDO configurável
10540 VDO 1 Output setpoint 4
VDO 102 configurações são disponíveis apenas no Utility Software
AGC-3 Alarm and Parameter List
DEIF A/S Page 110 of 112
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
10540 VDO 1 outp. Setp. 4 -49 482 80
Designers Reference Handbook
Curva da VDO configurável
10550 VDO 1 Input setpoint 5
10550 VDO 1 inp. Setp. 5 0 Ohm
480 Ohm 184 Ohm
Designers Reference Handbook
Curva da VDO configurável
10560 VDO 1 Output setpoint 5
10560 VDO 1 outp. Setp. 5 -49 482 100
Designers Reference Handbook
Curva da VDO configurável
10570 VDO 1 Input setpoint 6
10570 VDO 1 inp. Setp. 6 0 Ohm
480 Ohm 200 Ohm
Designers Reference Handbook
Curva da VDO configurável
10580 VDO 1 Output setpoint 6
10580 VDO 1 outp. Setp. 6 -49 482 110
Designers Reference Handbook
Curva da VDO configurável
10590 VDO 1 Input setpoint 7
10590 VDO 1 inp. Setp. 7 0 Ohm
480 Ohm 210 Ohm
Designers Reference Handbook
Curva da VDO configurável
10600 VDO 1 Output setpoint 7
10600 VDO 1 outp. Setp. 7 -49 482 115
Designers Reference Handbook
Curva da VDO configurável
10610 VDO 1 Input setpoint 8
10610 VDO 1 inp. Setp. 8 0 Ohm
480 Ohm 220 Ohm
Designers Reference Handbook
Curva da VDO configurável
10620 VDO 1 Output setpoint 8
10620 VDO 1 outp. Setp. 8 -49 482 120
Designers Reference Handbook
Curva da VDO configurável
VDO 105 Configurações 10630–10790 igual para as configurações do VDO 102 (10460-
10620)
VDO 108 configurações estão apenas disponíveis no Utility Software.
AGC-3 Alarm and Parameter List
DEIF A/S Page 111 of 112
VDO 108
Selecionar Multi-entradas
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
10970 Unidades De Medidas
10970 Engineering units Bar/Celsius Psi/Fahrenheit
Bar/Celsius
10980 Multi-entradas configuráveis 102
10980 Multi inp.comf. 102 4-20 mA Binary 0-40 V DC
Possible selections: 4-20 mA 0-40 V DC Pt100 Pt1000 VDO oil pressure VDO water temp VDO fuel level Binary
10990 Multi-entradas configuráveis 105
10990 Multi inp.comf. 105 4-20 mA Binary 0-40 V DC
Seleções possíveis: 4-20 mA 0-40 V DC Pt100 Pt1000 VDO oil pressure VDO water temp VDO fuel level Binary
11000 Multi-entradas configuráveis 108
11000 Multi inp.comf. 108 4-20 mA Binary 0-40 V DC
Seleções possíveis: 4-20 mA 0-40 V DC Pt100 Pt1000 VDO oil pressure VDO water temp VDO fuel level Binary
Configurações 10800–10960 igual para as configurações do VDO 102 (10460-10620)
VDO 108 configurações estão apenas disponíveis no Utility Software.
AGC-3 Alarm and Parameter List
DEIF A/S Page 112 of 112
Saídas Digitais Externa
No. Setting Min.
Max.
Factory setting
Notes Ref. Description
12790 Ext. dig. out 1
Ext. dig. out 1 Function Alarm Limit Horn
Alarm
Ext. dig. out 1 OFF delay 0.0 s 999.9 s
5.0 s
Opção: I/O dos módulos externos
(H8)
Status Do Módulo Externo
No. Setting Min.
Max.
Notes Ref. Description
12950 Ext module 0 STATUS
-32768 +32768
Opção: I/O dos módulos
externos (H8)
Este é um número lido no módulo externo e exibido na USW apenas. Por favor, consulte a descrição da opção H8 para obter detalhes
DEIF A/S reserves the right to change any of the above.
O mesmo para as definições de 12800 – 12940.
O mesmo para as definições de 12951-12983 (modulo externo de 1 ao 33).