Procedimento de Configuração de Roteadores HP

8/20/2019 Procedimento de Configuração de Roteadores HP

1/91

H3C

MSR20_MSR30_MSR50_MSR900-CMW520-R2209P33-SI Release Notes

Copyright © 2012 Hangzhou H3C Technologies Co., Ltd. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any

means without prior written consent of Hangzhou H3C Technologies Co., Ltd.

The information in this document is subject to change without notice.


2/91

1

H3C

MSR20_MSR30_MSR50_MSR900-CMW520-

R2209P33-SI Release NotesKeywords: Version Information Unresolved Problems and Avoidance Measure

Abstract: The explication for this version, including Version Information, Unresolved

Problems and Avoidance Measure, Version Compatibility, Software Upgrading and so on.

Acronyms:

Acronym Full spelling

LAN Local Area Network

MAC Media Access ControlIGMP Internet Group Management Protocol

VLAN Virtual Local Area Network

STP Spanning Tree Protocol

RMON Remote Monitor(SNMP)

GMRP GARP Multicast Registration Protocol

ACL Access Control List

DHCP Dynamic Host Configuration Protocol

OSPF Open Shortest Path First

RIP Routing Information Protocol

ARP Address Resolution Protocol

AAA Authentication Authorization Accounting

RSTP Rapid Spanning Tree Protocol

PIM Protocol Independent Multicast

LPM Longest Prefix Match

QoS Quality of Service

UTP Unshielded Twisted Paired

SFP Small Form-Factor Pluggable

GBIC Gigabit Interface Converter


3/91

2

Table of Contents

Version Information ················································································································· 5

Version Number ······················································································································· 5

Version History·························································································································· 5 Hardware and Software Compatibility Matrix ············································································ 12

Upgrading restrictions and guidelines ······················································································· 15

Hardware feature updates ···································································································· 15

CMW520-R2209P33 ················································································································· 15

CMW520-R2209P26 ················································································································· 15

CMW520-R2207P08 ················································································································· 15

CMW520-E2103 ······················································································································ 16

CMW520-E1804 ······················································································································ 16

CMW520-B1707 ······················································································································ 16

CMW520-B1608 ······················································································································ 17

CMW520-B1506 ······················································································································ 17

Software feature and command updates ··············································································· 17

MIB Updates ························································································································· 17

Configuration Changes ········································································································· 21

Restrictions and Cautions ······································································································ 21

Open Problems and Workarounds ·························································································· 22

List of Resolved Problems ······································································································· 22 Resolved Problems in CMW520-R2209P33 ················································································· 22

Resolved Problems in CMW520-R2209P26 ················································································· 23





Resolved Problems in CMW520-R2209 ······················································································ 26









Resolved Problems in CMW520-E2206 ······················································································· 31

Resolved Problems in CMW520-E1908P02 ·················································································· 32

Resolved Problems in CMW520-E1804 ······················································································· 32

Resolved Problems in CMW520-B1707······················································································· 32



Resolved Problems in CMW520-R1508P02&CMW520-B1508P02 ···················································· 35

Resolved Problems in CMW520-R1508&CMW520-B1508 ······························································ 35



Resolved Problems in CMW520-B1501L01 ·················································································· 37

Resolved Problems in CMW520-B1204P04 ················································································· 37




4/91

3







Related Documentation ········································································································ 41

New Feature Documentation ·································································································· 41

Documentation Set ················································································································ 41

Obtaining Documentation ······································································································ 41

Technical support ················································································································· 42 Files ································································································································ 60

Software Maintenance Methods ······················································································· 62

Main BootWare Menu ······································································································ 63

BootWare Submenus ······································································································· 66

Introduction to XModem ·································································································· 69

Modifying Serial Port Parameters ······················································································· 69

Configuring Ethernet Parameters ······················································································ 73

Upgrading Application Program Through Ethernet Interface ················································ 75

Maintaining the Router with TFTP Server·············································································· 77

Maintaining the Router with FTP Server ··············································································· 79

Maintaining Application Program and Configuration File ····················································· 83

User Password Loss ··········································································································· 85

BootWare Password Loss ·································································································· 86

Super Password Loss ········································································································ 87


5/91

4

List of Tables

Table 1 Version history ................................................................................................................................. 5

Table 2 Hardware and software compatibility matrix .........................................................................12

Table 3 MIB updates..................................................................................................................................17

Table 4 Follow these steps to register the software: .............................................................................22

Table 5 MSR20-1X Series Hardware Features .........................................................................................43

Table 6 MSR20 Series Hardware Features ..............................................................................................44


Table 8 MSR30 -1X Series Hardware Features ........................................................................................46


Table 10 MSR 9XX Series Hardware Features .........................................................................................48

Table 11 MSR20_MSR30_MSR50_MSR900 series Module List ................................................................49

Table 12 MSR20_MSR30_MSR50_MSR900 Series Software Features ....................................................55

Table 13 Default names and types of the boot files ............................................................................60

Table 14 Description on the three configuration files ..........................................................................61

Table 15 Main BootWare menu ...............................................................................................................65

Table 16 BootWare serial submenu ........................................................................................................66

Table 17 Enter Ethernet interface submenu ..........................................................................................67

Table 18 File control submenu .................................................................................................................68

Table 19 BootWare operation submenu ................................................................................................68

Table 20 Ethernet parameters settings description ..............................................................................74


6/91

5

This document describes the features, restrictions and guidelines, open problems, and

workarounds for version R2209P33. Before you use this version in a live network, back up the

configuration and test the version to avoid software upgrade affecting your live network.

Use this document in conjunction with H3C

MSR20_MSR30_MSR50_MSR900-CMW520-R2209P33-SI Release Notes (Software Feature

Changes) and the documents listed in "Related Documentation".

Version Information

Version Number

MSR 20-20_MSR 20-21_MSR 20-40_MSR30-16_MSR 30-20_MSR 30-40_MSR 30-60_MSR

50-40_MSR 50-60_MSR 50-40 MPU-G2_ MSR 50-60 MPU-G2:

Comware software, Version 5.20, Release 2209P33, Standard

MSR9XX_MSR20-1X_MSR30-11_MSR30-1X:

Comware software, Version 5.20, Release 2209P33

Note: You can see the version number with the command display version in any view.

Please see Note

.

Version History

Table 1 Version history

Versionnumber

Lastversion

ReleaseDate

Release

typeRemarks

CMW520-R

2209P33

CMW520-

R2209P262012-08-21

Release

version

Support MSR20_30_50_900 series

Modified Features:

1. Logging in to the device

2. The specifications of ASBR LSP and BGP LSP

CMW520-R

2209P26

CMW520-

R2209P21 2012-07-23

Release

version


Modified Features:1. Logging in to the device

CMW520-R

2209P21

CMW520-

R2209P15

2012-06-14

Release

version


New Features:

1. Support map a nonstandard port to an

application layer protocol for NAT ALG

2. The console interface of MSR900 and

MSR920 support the function of the auxiliary

interface, and Only the MSR900 and MSR920

which's PCB versions are 3.0 or higher can

support this function.

CMW520-

R2209P19

Release

version


7/91

6

CMW520-R

2209P19

CMW520-

R2209P012012-06-14

Release

versionOnly support MSR9XX series

CMW520-R

2209P15

CMW520-

R2209P132012-05-17

Release

version


New Features:

1. Support to auto-configure the router by USB

disk

2. Extend MSR50 OSPF maximum area amount

to 200

CMW520-R

2209P13

CMW520-

R2209P012012-04-23

Release

version


New Features:

1. Support to disable the USB port using the

command

CMW520-R

2209P01

CMW520-

R22092012-03-28

Release

version


New Features:

1. Support to filter packets based on MAC

Addresses, and any attempt to break this rule

must to be logged and to send a SNMP trap2. Support to assign IPv6 address of /127 prefix

on link interfaces

CMW520-R

2209

CMW520-

R2207P452012-02-14

Release

version


New Features:

1. CWMP support for configuring multiple ACS

servers.

2. Support multicast UDPH function

3. Support to using the sub-address of the

interface sending and receiving RIP routes

CMW520-R

2207P45

CMW520-

R2207P382011-12-28

Release

version


New Features:

1. Using the command of ―impedance

south-africa‖ to set the FXO interface‘s ringing

impedance

2. Support HUAWEI EC1261 3G modem

3. If The NAT and IPSEC functions were

enabled at the same interface, the command

of ―ipsec no-nat-process enable‖ can control

that packets don‘t do NAT transition before

IPSEC

4. Support of CWMP over AES-256 SSL tunnel

5. Support of CWMP (TR-069) over SSL for BIMSand the router

CMW520-R

2207P38

CMW520-

R2207P342011-11-18

Release

version


New Features:

1. The MIM-G.SHDSL and FIC-G.SHDSL card

supported the Whip function

CMW520-R

2207P34

CMW520-

R2207P232011-10-19

Release

version


New Features:

1. Support Huawei E261 3G modem and ZTE

MF190 3G modem


8/91

7

CMW520-R

2207P23

CMW520-

R2207P142011-09-15

Release

version


New Features:

1. Delay to notify the status change of

interface

2. Support to encrypt HWTACAS Key

3. The Statistic information of the MFR main

interface included the input and outputpackets from sub-interface.

CMW520-R

2207P14

CMW520-

R2207P082011-08-17

Release

version


New Features:

1. The number of NAT address pool was

extended to 64 from 32.

2. Support Sierra 250U and 308U 3G modem at

the MSR20/MSR30/MSR9XX router.

CMW520-R

2207P08

CMW520-

R2207P022011-07-15

Release

version


New Features:

1. Support HUAWEI E173 WCDMA modem2. Support to Configure TPID on a Layer 3

Ethernet or VE interface, and to implement

VLAN termination.

3. Support to transit the

extendedVideoCapability field of H245

packets in the NAT ALG

4. Support the DVPN instance.

5. The QoS policy of main interface can apply

to sub-interface.

6. Support the Refer-by field of the SIP packets.

CMW520-R

2207P02

CMW520-

R22072011-06-23

Releaseversion

Support MSR20_30_50_900 seriesNew Features:

1. Support the statistics per classifier of nested

QoS

CMW520-R

2207

CMW520-

E22062011-05-19

Release

version


New Features:

1. Call forwarding authority control

2. Support DAR MIB

CMW520-E

2206

CMW520-

E21032011-04-07

ESS

version


New Features:

1. Support Novatel Modem MC760

2. Authorization again for AAA

3. The feature supports the VPN could visit the

other VPN by NAT

4. Support OSPF and NAT in bridge-template

interface

5. WCDMA 3G Modem

6. CDMA2000 3G Modem

7. TD-SCDMA 3G Modem

8. SIP TRUNKING


9/91

8

9. SRTP

10. L2VPN connected to L3VPN

11. NAT DMZ host and related features

12. SIP support for non early media negotiation

13. IPsec RRI

14. Allows you to configure NAT address

groups, NAT server, and attack protection

through TR069.

15. Support of routing protocols for 6VPE

16. BIDIR-PIM

17. OSPFv3 support for MCE

18. Voice support for TR104

19. BGP, OSPFv3 and ISISv6 support for IPv6

VPN BFD

20. Allows you to set a BGP update interval of

0.

21. Allows you to use domain names to specify

SNMP trap and log hosts.

22. TR069 supports the following memory and

CPU utilization nodes:

23. ACL configuration information display

filtering

24. A routing policy name can contain up to

64 characters.

25. Allows you to use names as BGP

community attributes

26. Permanent attribute for static routes

27. Continue feature for routing policy

28. E1POS and AM ports can send calling

numbers.

29. POS terminal access can use the source

address in the TPDU header to map POS

packets to specific POS applications.

30. POS terminal access allows you to specify

TCP source port numbers for POS applications.

31. Bloomberg MSR Source NAT

In NAT NOPAT mode (NOPAT dynamic entries

exist)

32. NAT support for discontinuous address

pools33. ISDN support for sending the

progress-indicator unit

34. An ACL name can contain up to 63

characters.

35. POS MIB and E1 POS MIB

36. SIP support for SRV and NAPTR

37. TR098

CMW520-E

2103

CMW520-

E1908P022010-03-24

ESS

version


New Features:


10/91

9

1. Portal, RADIUS, and HWTACACS support for

multi-VRF

2.L2TP Auto Client

3.G729B audio codec, which supports G.729

Annex B

4.FXS interface support for calling name

5. NQA threshold alarming

6. Dot1p based remark for MPLS-EXP, which

allows you to implement priority scheduling on

an MPLS interface.

7.Virtual baudrate adjustment on the tunnel

interface

8.Support for 63-bit SIP authentication

username

9.ISDN trap, which provides the state change

traps of ISDN Layer-2

10.MQC MIB Index Persist, which enables MQC

MID indexes to survive reboots

11. Layer-3 interface support for LLDP, whichenables Layer-3 Ethernet interfaces to support

LLDP.

CMW520-E

1908P02

CMW520-

E18042009-09-18

ESS

version

Support MSR20_30_50 series(Add

MSR30-1Xseries and MSR9XX series)

New Features:

1. SIP-T‘s support for basic QSIG call

2. E&M non-signaling mode

3. Support for unidirectional media streams

4. Portal‘s support for mandatory web page

pushing5. Support for enhanced fax and modem

transparent transmission

6. Tunnel interfaces‘ support for the IPSec

encapsulation

7. Optimizing the QoS page

8. Embedded NMS

9. AAA‘s support for super authentication

10. SIP‘s support for the Join header

11. Voice products‘ support for Web NMS

This feature implements using Web to

configure voice products.

CMW520-R

1809P06

CMW520-

R18092009-09-09

Release

versionOnly support MSR30-11_30-1X

CMW520-R

1809

CMW520-

R18082009-09-09

Release

versionOnly support MSR20_MSR30

CMW520-R

1805

CMW520-

E18042009-06-26

Release

versionOnly support MSR 20-1X

CMW520-E

1804

CMW520-

B17072009-03-02

ESS

version

Support MSR20_30_50 series(include MSR20-1X

and MSR50 MPU-G2)

New Features:


11/91

10

1.P2P flow control feature

2. Enhances for ARP anti-attack

3. Configure a fixed sub interface throughWeb.

4. TEL_URL

5. DDNS collaboration with VPN

6. Customized IVR

7. POS terminal access

8.DMC

9. DNS supported on voice features

10.IPsec&IKE Monitor MIB

11.SIP session update

12.Enable the implementation of SIP on the

router compatible with Huawei SoftX standard

T38 fax, FAX \ MODEM pass through function.

Deleted Features: None.

CMW520-R1719P01

CMW520-R1710

2009-02-20Releaseversion

Only support MSR 30-11

CMW520-R

1710

CMW520-

B17072008-12-17

Release

versionOnly support MSR 20-1X

CMW520-R

1710

CMW520-

B17072008-09-14

Release

versionOnly support MSR 30-11

CMW520-B

1707

CMW520-

B16082008-06-23

Beta

version

Support MSR20_30_50 series(include MSR20-1X

and MSR50 MPU-G2)

1.QoS priority marking support on VLAN

interfaces

2.Encryption of configuration file

3.Enhanced Netstream

4.Traffic classification and queuing support on

PPPoE-enabled interfaces in bridging mode

5.Embedding CBQ in QoS

6.ISDN NAT Backup

Deleted Features: None.

Modified Features: None.

CMW520-R

1618P15

CMW520-

R1618P032008-10-15

Release

versionOnly support MSR20

CMW520-R

1618P03

CMW520-

R1617 2008-06-20

Release

version Only support MSR20-1X

CMW520-R

1618P01

CMW520-

R16172008-08-22

Release

versionOnly support MSR30_30-16

CMW520-R

1617

CMW520-

R16152008-04-09

Release

versionOnly support MSR20

CMW520-R

1615

CMW520-

B16082008-03-10

Release

versionOnly support MSR30-11

CMW520-B

1608P05

CMW520-

B16082008-01-18

Beta

versionOnly support MSR20-1X


12/91

11

CMW520-B

1608

CMW520-

B16062007-11-29

Beta

versionSupport MSR20_30_50 series(except MSR20-1X)

CMW520-B

1606

CMW520-

R1508P01

2007-10-19

Beta

version

Support MSR20_30_50(except

MSR30-11/MSR20-1X)

New Features:

1.ACSEI

2.VoiceVLAN support Cisco IP Phone

Deleted Features:None.

Modified Features:None.

CMW520-B

1605P01H0

1

CMW520-

R1508P012007-09-20

Beta

version MSR20-1X

CMW520-R

1508P02

CMW520-

R15082007-09-24

Release

versionSupport MSR20_30_50(except MSR30-11)

CMW520-B

1508P02

CMW520-

B15082007-09-24

Beta


CMW520-R1508P01

CMW520-R1508

2007-09-20 Releaseversion

Only support MSR20_30

CMW520-B

1508

CMW520-

B1506P022007-09-07

Release


CMW520-R

1508

CMW520-

R15072007-09-03

Release

version

None.

New Features:

1.DVPN

2.Terminal Access

3.Qos WRED support DSCP

4.Call forwarding

5.Call waiting

6.Call hold

7.Call transfer

8.Call backup

9.Hunt group

10.Call barring

11.Extended Portal

12.SNMP support VPN



CMW520-R

1507

CMW520-

B15022007-08-02

Release

version

First time for the release version of

MSR30-16,and Support MSR20_30_50 (except

MSR30-11)

CMW520-B

1506P02

CMW520-

B1506P012007-08-02

Beta


CMW520-B

1506P01

CMW520-

B15062007-07-05

Beta


CMW520-B

1506

CMW520-

B15022007-06-18

Beta

version

First time for the release version of

MSR30-11,and only support MSR30-11

None.


13/91

12

CMW520-B

1502

CMW520-

B1501L012007-04-24

Beta

versionFirst time for the beta version of MSR30-16

CMW520-B

1501L01

CMW520-

B1204L012007-02-06

Beta

versionLimited.

CMW520-B

1204P04

CMW520-

B1204P032007-02-01

Beta

versionResolved Problem

CMW520-B

1204P03

CMW520-

B1204L022007-01-30

Beta


CMW520-B

1204L02

CMW520-

B12032007-01-25

Beta

versionLimited.

CMW520-B

1204L01

CMW520-

B12012007-01-19

Beta

versionLimited.

CMW520-B

1203P01

CMW520-

B12032006-12-30

Beta

versionLimited.

CMW520-B

1203

CMW520-

B1202P022006-12-27

Beta


CMW520-B1202P02

CMW520-B1202P01

2006-12-06 Betaversion

Resolved Problem

CMW520-B

1202P01

CMW520-

B12022006-11-23

Beta


CMW520-B

1202

CMW520-

B12012006-11-10

Beta


CMW520-B

1201

CMW520-

B11062006-10-30

Beta


CMW520-B

1106

CMW520-

B1105P012006-09-28

Beta


CMW520-B

1105P01

CMW520-

B1105 2006-08-25Beta

version Resolved Problem

CMW520-B

1105None 2006-08-09

Beta

versionFirst time.

Hardware and Software Compatibility Matrix

Table 2 Hardware and software compatibility matrix

Item Specifications

Product

familyMSR20_30_50_900 series routers

Hardwa

re

platfor

m

MSR20-1X series: MSR 20-10_MSR 20-11_MSR 20-12_MSR 20-13_MSR 20-15

MSR 20-20_MSR 20-21_MSR 20-40

MSR30-11

MSR30-1X series: MSR30-10_MSR30-11E_MSR30-11F

MSR 30-16

MSR30-20_MSR 30-40_MSR 30-60


14/91

13

Item Specifications

MSR 50-40_MSR 50-60_ MSR 50-40 MPU-G2_MSR 50-60 MPU-G2

MSR9XX series: MSR 900_MSR920

Boot

ROM

version

MSR20-1X series: 226 or higher

MSR 20-20_MSR 20-21_MSR 20-40: 313 or higher

MSR30-11_ MSR30-1X series: 223 or higherMSR30-16: 212 or higher

MSR 30-20_MSR 30-40_MSR 30-60: 317 or higher

MSR 50-40_MSR 50-60: 315 or higher

MSR 50-40 MPU-G2_ MSR 50-60 MPU-G2: 122 or higher

MSR 9XX series: 117 or higher

(Note: Perform the command display version command in any view to view the version

information. Please see Note②)

Host

softwar

e

Hardware software MD5 Check Sum

MSR 20-20_MSR

20-21_MSR 20-40

MSR20-CMW520-R2209P21-SI

.BIN

c541858f8b13651136b303e03

51d0062

MSR20-1X seriesMSR201X-CMW520-R2209P21

.BIN

8c7e0e86f45b6fed0384b6b0c

838a62b

MSR 30-11MSR3011-CMW520-R2209P21

.BIN

be88510a3389d09897a9cffd0

7bb70a9

MSR30-1X seriesMSR301X-CMW520-R2209P21

.BIN

be88510a3389d09897a9cffd0

7bb70a9

MSR 30-16MSR3016-CMW520-R2209P21

-SI.BIN

5ee61ceec043f8d7f606bd3d5

1e2383a

MSR 30-20_MSR

30-40_MSR 30-60

MSR30-CMW520-R2209P21-SI

.BIN

aad04409516911fd91d52a102

b14949d

MSR 50-40_MSR 50-60MSR50-CMW520-R2209P21-SI

.BIN

08791c5fcb8b8bdaf37045908

3a56cf2

MSR 50-40 MPU-G2_ MSR

50-60 MPU-G2

MSR50-CMW520-R2209P21-E

PUSI.BIN

d519182f3fe51940e99c22a1a

722e9b3

MSR 900_MSR920MSR9XX-CMW520-R2209P21.

BIN

626e88e80fadfa44b77015e81

2418b7d

iMC

version

iMC PLAT 5.1 SP1 (E0202P05)

iMC UAM 5.1 SP1 (E0301P03)

iMC EAD 5.1 SP1 (E0301P03)

iMC MVM 5.1 SP1 (E0201P01)

iMC VSM 5.1 (E0201) (MSR9XX series not support VSM)

iMC QoSM 5.1 (E0201)

iMC TAM 5.1 (E0301)

iNode

versioniNode PC 5.1 (E0304)

TTYD

version4.27

OAA

version

OAA Name Version

OAP (1) MIM-OAP/ FIC-OAP version:


15/91

14

Item Specifications

Software: 130 or higher

(2) MIM-OAP-V2 version:


BIOS: 103 or higher

FPGA: 1.00 or higher(3) FIC-OAP-V2 version:

Software: 102or higher

BIOS: 102 or higher

FPGA: 1.00 or higher

OAPS

(1) MIM-OAPS version:


(2) MIM-OAPS-V2 version:

Software: 104or higher

BIOS: 101 or higher

FPGA: 1.00 or higher

OSM 128 or higher

ASM 102 or higher

NAM 200 or higher

WAAM 100 or higher

VCX VCX 9.5 or higher

Cards

Version

Cards Name Software Version CPLD or FPGA version

SIC-3G-GSM 180 or higher 200 or higher

SIC-3G-CDMA 180 or higher 200 or higher

SIC-3G-TD 180 or higher 200 or higher

SIC-AP R3200 or higher 200 or higher

SIC-ADSL-I/SIC-ADSL-P 230 or higher 100 or higher

MIM-6FCM/FIC-6FCM 230 or higher 100 or higher

SIC-EPON R3130 or higher 100 or higher

FIC-24FXS 200 or higher 100 or higher

DFIC-24FXO24FXS 200 or higher 100 or higher

SIC-2BSV/MIM-2BSV/FIC

-2BSV

None CPLD：200 or higher

VCPM：RTV1VCPM NoneCPLD：100 or higher

FPGA：400 or higher

Sample：To display the host software and Boot ROM version of the MSR routers, perform the

following:

display version

H3C Comware Platform Software

Comware software, Version 5.20, Release 2209P33, Standard ------- Note


16/91

15

Copyright (c) 2004-2012 Hangzhou H3C Tech Co., Ltd. All rights reserved.

H3C MSR50-60 uptime is 0 week, 0 day, 0 hour, 2 minutes

CPU type: FREESCALE MPC8541 833MHz

256M bytes DDR SDRAM Memory

4M bytes Flash Memory

Pcb Version: 3.0

Logic Version: 2.0

Basic BootROM Version: 3.10

Extend BootROM Version: 3.15 ------ Note

[SLOT 0]CON (Hardware)3.0, (Driver)1.0, (Cpld)2.0

[SLOT 0]AUX (Hardware)3.0, (Driver)1.0, (Cpld)2.0

[SLOT 0]GE0/0 (Hardware)3.0, (Driver)1.0, (Cpld)2.0

[SLOT 0]GE0/1 (Hardware)3.0, (Driver)1.0, (Cpld)2.0

[SLOT 11]FIX-SNDE (Hardware)3.0, (Driver)2.0, (Cpld)2.0

Upgrading restrictions and guidelines

Hardware feature updates

CMW520-R2209P33

None

CMW520-R2209P26

New features: TOSHIBA flash is supported on MSR 30-11E/MSR 30-11F/MSR 30-10/MSR

900/MSR 920.

Deleted features: None

CMW520-R2207P08

New Features:

Add new card:

Open Application Platform MIM Interface Module(Smart)-V2 (RT-MIM-OAPS-V2)

Open Application Platform MIM Interface Module-V2 (RT-MIM-OAP-V2)

Open Application Platform FIC Interface Module-V2 (RT-FIC-OAP-V2)


17/91

16

CMW520-E2103

New Features:

Add new card:

1-port SDH/SONET interface module FIC-1POS-V4;

1-port SDH/SONET interface module MIM-1POS-V2;

1-port channelized SDH/SONET interface module FIC-1CPOS;

1 port E1POS POS-terminal access module FIC-E1POS;

4-port voice subscriber circuit & 1-port voice AT0 analog trunk interface card

-DSIC-4FXS1FXO

CMW520-E1804New Features:

Add new card:

1-port EPON interface card (SIC-EPON);

3G WLAN access module (SIC-3G-GSM);

802.11b/g WLAN access module (SIC-WLAN-b/g);

802.11n WLAN access module (SIC-WLAN-n).

CMW520-B1707

New Features:

Add new card:

RT-SIC-1E1-F-H3

RT-SIC-2E1-F-H3

RT-MIM-8FXS-8FXO-H3

RT-MIM-16FXS-H3

RT-MIM-1CT3-V2-H3

RT-MIM-1CE3-V2-H3

RT-MIM-1ATM-OC3-H3

RT-DMIM-48FSW-H3

RT-FIC-1CE3-V3-H3


18/91

17

RT-FIC-1CT3-V3-H3

RT-FIC-1ATM-OC3-H3


CMW520-B1608New Features:

Add 2-port voice subscriber circuit & 1-port voice AT0 analog trunk interface

card(SIC-2FXS1FXO);

1/2-port ISDN BRI S/T voice interface card can be supported on MSR20/30/50series and

MSR30-11/30-16.(the card can not be support on 2 slot of MSR30-11).


CMW520-B1506

New Features:MSR3011, Please make reference to Table4.



Software feature and command updates

For more information about the software feature and command update history, see H3C

MSR20_MSR30_MSR50_MSR900-CMW520-R2209P33-SI Release Notes (Software Feature

Changes).

MIB Updates

Table 3 MIB updates

Version

Number ItemMIB File

Name

Module

Name Description

CMW520-R

2209P01

New None None None

Modi

fied

hh3c-confi

g-man.mib

HH3C-CONFIG-

MAN-MIB

Modified the description of

hh3cCfgLogTerminalUser in

hh3cCfgLogTable

Delet

edNone None None

CMW520-R

2209

New None None None

Modi rfc1213.mi RFC1213-MIB Modified all the descriptions


19/91


20/91

19

Hh3c-e1t1

vi.mib

HH3C-E1T1VI-MI

B

Add

hh3cE1T1VITrapTimeSlotEnabl

e

hh3c-e1.mi

bHH3C-E1-MIB

Add hh3ce1FcmChannelIndex

and hh3ce1TimeSlotSetTable

Modi

fied

hh3c-splat-mstp.mib

HH3C-LswMSTP-MIB


hh3cdot1sMstAdminFormatSelector. Changed the value

range from [0..255] to 0

hh3c-dhcp

s.mib

HH3C-DHCPS-M

IB


hh3cDHCPSGlobalPoolLeaseU

nlimited. Added the value

can‘t be set to 0

rfc1657-bg

p4.mibBGP4-MIB

Modified the PDS of

bgpeerAdminStatus,

bgpPeerHoldTimeConfigured,

bgpPeerKeepAliveConfigure

d,

bgpPeerMinASOriginationInterval and

bgpPeerMinRouteAdvertisem

entInterval

Hh3c-posa

.mib

HH3C-POSA-MIB

Modified the PDS of

hh3cPosaTerminalTable and

hh3cPosaAppTable

Delet

edNone None None

CMW520-E

2103New

hh3c-radiu

s.mib

HH3C-RADIUS-

MIB

Addedhh3cRadiusAuthErrThredsholdin HH3C-RADIUS-MIB

hh3c-pppo

e-server.mi

b

HH3C-PPPOE-SE

RVER-MIB

Added

HH3C-PPPOE-SERVER-MIB

hh3c-dhcp

-server.mib

HH3C-DHCP-SE

RVER-MIB

Added

hh3cDHCPServerAvgIpUseThr

eshold,

hh3cDHCPServerMaxIpUseThr

eshold,

hh3cDHCPServerAllocateThre

shold in

hh3cDHCPServerObjects in

HH3C-DHCP-SERVER-MIB

hh3c-ip-ad

dress.mib

HH3C-IP-ADDRE

SS-MIB

Added

hh3cIpAddrNotifyScalarObjec

ts in HH3C-IP-ADDRESS-MIB

hh3c-3gm

odem.mib

HH3C-3GMODE

M-MIBAdded HH3C-3GMODEM-MIB

hh3c-isdn.

mibHH3C-ISDN-MIB

Added

hh3cLapdStatusTrapEnable

and

hh3cLapdIsdnStatusChange

in HH3C-ISDN-MIB


21/91

20

rfc2128-dia

l-control.mi

b

DIAL-CONTROL-

MIBAdded DIAL-CONTROL-MIB

hh3c-voice

-call-activ

e.mib

HH3C-VOICE-C

ALL-ACTIVE-MIB

Added

HH3C-VOICE-CALL-ACTIVE-MI

B

hh3c-voice-dial-contr

ol.mib

HH3C-VOICE-DIAL-CONTROL-M

IB

AddedHH3C-VOICE-DIAL-CONTROL-

MIB

rfc1213.mi

bRFC1213-MIB

Added RFC1213 IP Group and

ICMP Group

lldp.mib LLDP-MIB Added LLDP-MIB

lldp-ext-do

t1.mib

LLDP-EXT-DOT1-

MIBAdded LLDP-EXT-DOT1-MIB

lldp-ext-do

t3.mib

LLDP-EXT-DOT3-

MIBAdded LLDP-EXT-DOT3-MIB

Modi

fied

hh3c-isdn.mib

HH3C-ISDN-MIB

Modified

hh3cLapdIsdnProtocol in

HH3C-ISDN-MIB

hh3c-flash-

man.mib

HH3C-FLASH-M

AN-MIB

Modified description of

hh3cFlhOperType in

hh3cFlhOpTable of

HH3C-FLASH-MAN-MIB

rfc2465-ipv

6.mibIPV6-MIB

Modified route scalar objects

and ipv6RouteTable of

IPV6-MIB

hh3c-splat-

inf.mib

HH3C-LswINF-MI

B


hh3cMaxMacLearnRange of

HH3C-LswINF-MIB

rfc4444-isis.

mibISIS-MIB

Changed describe of

isisSysWaitTime of ISIS-MIB to

support read operation

ieee8023-l

ag.mib

IEEE8023-LAG-

MIB


dot3adAggPortActorAdminSt

ate of IEEE8023-LAG-MIB

hh3c-cbqo

s2.mib

HH3C-CBQOS2-

MIB


hh3cCBQoSMatchRuleType of

HH3C-CBQOS2-MIB

Delet

ed

None None None

CMW520-E

1908P02

Newrfc2662-ad

sl-line.mib ADSL-LINE-MIB Added ADSL-LINE-MIB

Modi

fiedNone None None

Delet

edNone None None

CMW520-B

1608 Delet

ed

h3c-e1t1vi.

mibH3C-E1T1VI-MIB

Added whole module of

h3c-e1t1vi.mib

huawei-dh HUAWEI-DHCPS Add hwDHCPSIPInUseExTable


22/91

21

cps.mib -MIB to HUAWEI-DHCPS-MIB

Modi

fied

rfc2819

MIB.mib RMON-MIB

Modify descripsion Not

supported. When eventType is

none(1) or log(2), the value of

eventCommunity will not be

saved; when eventType is

snmptrap(3) or logandtrap(4),

the value of eventCommunitywill be saved but can take no

effect.

ieee8021x.

mib

IEEE8021-PAE-M

IB

Modify descripsion Only valid

on portbased method.

h3c-acl.mi

b H3C-ACL-MIB

When the value of

h3cAclIPAclAdvancedProtoc

ol is ICMP or ICMPV6,

h3cAclIPAclAdvancedIcmpTy

pe and

h3cAclIPAclAdvancedIcmpC

ode can be set, otherwise it

can not.

Delet

ed

huawei-spl

at-mam.mi

b

HUAWEI-LswMA

M-MIB

Deleted

hwdot1qMacSearchTable

CMW520-R

1508P02

New None. None. None.

Modi

fied

hh3c-user.

mibHH3C-USER-MIB

Modify h3cUserIndex PDS

attribute to "No".

hh3c-radiu

s.mib

HH3C-RADIUS-

MIB

Modify h3cRdAccRealTime

Description to "As per mib".

rfc4133-ent

ity.mibENTITY-MIB Modify "AR" to "MSR".

Delet

edNone. None. None.

Configuration Changes

None.

Restrictions and Cautions1. The versions of MSR30-11 can‘t boot based on 16M FLASH.

2. Software register is provided on the device to protect the authorized users‘ legal rights to

use the software. Trial period is set on the software with this function and users are required

to register the serial number of the software in the trial period. If the software has not been

registered until the trial period expires, the system automatically restarts every 30 minutes.


23/91

22

You can obtain a registration serial number through buying letter of authorization of the

software.

You can use the license register serial-number command or log onto the network

management interface and then enter the serial number to finish software registration; and

you can use the display license command or log onto the network management interface

to view the soft registration information of the device.

Table 4 Follow these steps to register the software:

To do... Use the command... Remarks

Register the softwarelicense register

serial-number

Required

Available in user view

Display the information display license any view

CAUTION:

H3C MSR 20-1X, MSR 30-11, MSR 30-1X and MSR 9XX not support Software register!

3.

It is recommended that the MSR900 and MSR920 which's PCB versions are 3.0 or higher

use the software R2209P19 or later versions. If the old software versions are used, the

console interface of the MSR900 and MSR920 will be flow controlled, and it is necessary to

forbid detecting the RTS/CTS signal at the terminal software in order to manage the

console interface normally.

Open Problems and WorkaroundsNone.

List of Resolved Problems

Resolved Problems in CMW520-R2209P33

RTD063126

Description: UDP Helper enabled on a VLAN interface works abnormally.

Condition: This symptom might occur on a VLAN interface configured with the udp

helper server command.

RTD062784

Description: The idle timer on a dialer interface that is a member port of an MP

interface does not take effect. As a result, the link on the dialer interface cannot be

automatically torn down when the idle timer expires.


24/91

23

Condition: This symptom might occur when the following conditions exist:

The MP interface comprises multiple dialer interfaces that have come online.

The dialer threshold and dialer timer commands have been configured on the

target dialer interface.


RTD062342

Symptom: Memory leaks occur if an ADSL port configured with MPPPoA has forwarded

large amounts of traffic for a certain time.

Condition: This symptom might occur if an ADSL port configured with MPPPoA has

forwarded large amounts of traffic for a certain time.

RTD062305

Symptom: A router reboots after processing H323 and ISDN DSS1 calls for a long time.

Condition: This symptom might occur if the router is installed with multiple VE1 cards

and has processed H323 and ISDN DSS1 calls for a long time.

RTD062240

Symptom: A walk of the RFC1213 ifConnectorPresent MIB node on a subinterface

returns an incorrect value.

Condition: This symptom can be seen after a walk of the RFC1213 ifConnectorPresent

MIB node on a sub interface.

RTD062168

Symptom: The URI in the SIP header fields translated by NAT ALG has an error, resulting

in a call failure.

Condition: This symptom might occur if the URL in the SIP header field uses TEL_URL

format.

RTD062634

Symptom: Transient traffic interruption occurs on the fixed FSW interface of MSR 30-11F

when the maximum number of MAC addresses is configured on the interface.

Condition: This symptom might occur if the maximum number of MAC addresses is

configured on the fixed FSW interface of MSR 30-11F.

RTD062492

Symptom: Packet loss occurs on a POS port if 80 M user traffic or more is forwarded on

the port.


25/91

24

Condition: This symptom might occur if 80 M user traffic or more is forwarded on the

POS port and most packets are smaller than 256 bytes packets because a POS port

cannot forward large amounts of small packets.

RTD062139

Symptom: An MSR 30-11E cannot receive multicast and broadcast packets if the

configured multicast or broadcast suppression threshold is smaller than 190pps.

Condition: This symptom might occur if the configured multicast or broadcast

suppression threshold is too small.

RTD062766

Symptom: The fixed GE0/GE1 interfaces of MSR 30 series might receive and send

packets abnormally.

Condition: This symptom might occur on some MSR 30 routers because the chips used

by these routers have defects.


RTD062073

Description: Because the external 3G modem negotiates slowly, if the PPPoE client

waits for PPP negotiation more than 10s, the PPPoE dialer will fail.

Condition: MSR device as PPPoE client, and connected with external 3G modem.

RTD061928

Description: The power level measured is greater than the maximum power level

allowed by the standard 12.5dBm.

Condition: The test house carries out the Annex L testing for the SIC-ADSL card.

RTD061985

Description: The UMTS light on the SIC-3G-GSM or SIC-HSPA card is bright yellow all

along.

Condition: The SIM card can‘t be identified in the SIC -3G-GSM or SIC-HSPA.


RTD061429

Description: When modifying the parameter of tunnel bandwidth, OSPF COST doesn‘t

update.

Condition: The tunnel interface of the route runs OSPF protocol.


26/91

25

RTD61366

Description: The REINVITE message from the router doesn‘t take NTE capacity filed, so

the FAX passthrough with LYNC server fails.

Condition: The router runs FAX passthrough with Microsoft LYNC server.

RTD061122Description: The router doesn‘t eliminate the NAT session synchronously at the router,

so that the NAT data flow can be transmitted all along.

Condition: Remove the NAT static configuration at the router, at the same time there

are durative NAT data flow at the router.


RTD060728

Description: Some time, the E1-F interface is UP and DOWN ceaselessly.

Condition: A SIC-2E1-F card is inserted into the router, and the link status of one E1-F

interface is UP, the link status of the other E1-F interface is DOWN.

RTD60727

Description: The router can‘t detect the RPS power status accurately, so there are lots

of RPS power alarms at the LOG of the router.

Condition: The MSR30 router with RPS power.

RTD60721

Description: Once the interface bearing the BGP connection is UP/DOWN, the BGP

connection will be UP/DOWN again and again, and it takes a long time to establish

the steady BGP connection.

Condition: There are lots of BGP route policies about community attribute at the router,

and there are also many of BGP routes at the router.

RTD60720

Description: The GTS characteristics (CIR, CBS, EBS) based on the real bandwidth

negotiated by the router on the display information are error.Condition: Set the QoS GTS policy at the ATM interface of the router.


RTD60406

Description: The router rebooted abnormally.

Condition: Insert some USB facility which the router can‘t support into the router.


27/91

26

RTD60172

Description: Certain instance, EC1261 doesn‘t reply BULK OUT ACK to the router for two

seconds, so the router can‘t identify the EC1261.

Condition: The router connects HUAWEI EC1261 MODEM.

RTD60042Description: After a long time, the FSW card can‘t forward multicast and broadcast

packets.

Condition: The 16FSW or 24FSW card at the router runs three layer packets, and the

other interfaces of the router forward large numbers of packets.

RTD59907

Description: E160 MODEM reboots again and again.

Condition: The router connects HUAWEI E160 MODEM.

RTD59895

Description: Period of time, The SIC-1T1-F card can‘t receive and send packets, and

the interface queue is plugged up.

Condition: The POE router is inserted into FSW-POE card and SIC-1T1-F card.

RTD60199

Description: The SNMP OID hh3cCfgLogTerminalUser value is error.

Condition: None.

Resolved Problems in CMW520-R2209

RTD59161

Description: When transmits some UDP packets, the router will reboot abnormally.

Condition: The router runs NAT function, and there are several NAT outbound

commands at the interface of the router.

RTD58793

Description: The result of NQA was inaccurate.

Condition: Run NQA function in the Multilink PPP link with several physical interfaces.

RTD58598

Description: The line protocol status of the async interface is always down.

Condition: The aysnc interface of the router works at flow mode.


28/91

27

RTD59306

Description: OSPF Area 0 ABR does not generate default to stub when no neighbor in

Area 0.

Condition: Run OSPF protocol in the router.


RTD58789

Description: If the router received challenge more than 16 bytes, the PPP CHAP

authentication failed.

Condition: The interface of the router set PPP protocol and CHAP authentication.

RTD58508

Description: The router can‘t identify the INARP packets with filled information, so therouter failed to parse the IP address.

Condition: None.

RTD57556

Description: Because the BGP timer of the router was inaccurate, the BGP neighbors

were UP and DOWN again and again.

Condition: The CPU usage of the router was high.

Resolved Problems in CMW520-R2207P38RTD57850

Description: There wasn‘t the command to adjust the cable attenuation parameters

at the IMA-T1 interface of the router.

Condition: None.

RTD57858

Description: The pulse shape of IMA-T1 interface was too low.

Condition: None.

RTD58297

Description: The pulse shape of SIC-EPRI interface has overshot /undershot.

Condition: None.

RTD58164

Description: The pulse shape of IMA-E1 interface was too low.

Condition: None.


29/91

28

RTD57892

Description: When the router received the SIP packets which‘s record-route and

contact head field the Transfer Protocol were inconsistent, because the router

selected the error Transfer Protocol the voice call failed。

Condition: The router as VOICE gateway connected with AYAYA .

RTD57811

Description: The dialer connection can‘t establish.

Condition: The Dialer interface of the router set chap authentication for call-in

connection.

RTD58221

Description: The router rebooted abnormally.

Condition: Execute the command of ―display ip flow-ordering statistic internal‖ at the

router.


RTD57852

Description: After the BFD session at the router was DOWN, the router would delete

correlative RIP routes, but the router still sent the RIP packets from the interface. If the

interface was broken down in the one direction, another end could still received the

rip packets.

Condition: The router started RIP BFD function.

RTD57785

Description: If the router received the SIP messages which the contact filed of was

included the maddr parameter, the voice call from the router was unsuccessful.

Condition: The router worked with some SIP SERVER, and established voice calls.

RTD57105

Description: The router reboots itself randomly.

Condition: The MSR30 router has 2 x 512M memories.


RTD57286

Description: Occasionally the router can‘t recover from PPP state-machine and can‘t

dialup 3G-link successfully.

Condition: The router doesn‘t receive connect information from 3G modem.


30/91

29

RTD57514

Description: The 3G interface of the router would be UP and DOWN.

Condition: 3G network was HSPA+.

RTD57365

Description: Because the SDP‘s fmtp and rtpmap of the SIP packet negotiated by error,

the compression selected was wrong.

Condition: The router established the SIP connection with other equipment.

RTD57500

Description: The packet which matching this route can‘t be transmitted.

Condition: MPLS L3VPN, inter-AS option B, a route advertising to ASBR through different

VPN-instance and the route is flapping.

Resolved Problems in CMW520-R2207P14RTD56973

Description: The 3G interface would be UP and DOWN because 3G network was

unstable.

Condition: 3G network status was unstable, little the network was no service.

RTD56986

Description: The router would turn off the FAX function, and brought on that the FAX

failed.

Condition: The router received the SIP INVITE message without a=T38MaxBitRate filed

to transfer T.38.


RTD56520

Description: Even though the RIP BFD session was down, the RIP routes were updated.

Condition: Configuring RIP BFD at the router, the link was uni-direction and the router

could receive the RIP packets.

RTD56390

Description: The router couldn‘t get the Calling number and Called Number attribute

from LAC.

Condition: The router acted as LNS, and LAC sent the ICCN packets without Proxy auth

attribute.


31/91

30

RTD56145

Description: Because the router didn‘t take offset filed in the L2TP packets, the L2TP

connection couldn‘t establish.

Condition: The router acted as LNS, and LAC requested the L2TP packets received

with offset field.


RTD56119

Description: The router will reboot possibly.

Condition: If change the DVPN tunnel-protocol when there is IP traffic going out of the

tunnel.

RTD56062

Description: The IPSec policy groups cannot be modified successfully if the virtual

interface is deleted first.

Condition: Apply two or more IPSec policy groups to a virtual interface on the web

interface, like interface tunnel.

RTD56060

Description: The router made mistake when negotiating about the codec, it resulted in

that the FAX failed.

Condition: The router received the SIP packet of ―200 OK‖ without

―a=silenceSupp:off‖.

RTD56106

Description: The DAR function was abnormal and couldn‘t identify the packets

correctly.

Condition: The packets were identified by DAR after the packets were transmitted

through L2TP tunnel.

RTD55818

Description: The E1 POS calls failed.Condition: The E1POS interface worked with ISDN signal, and established the ISDN

connection with ALCATEL PBX.

RTD56103

Description: The MSR router as RTA client couldn‘t establish connection with RTA relay.

Condition: The AR46 or AR28 router worked as RTA relay.


32/91

31


RTD54811

Description: The instant message cannot be relaid.

Condition:

When using UDP as the SIP transport protocol, If the Packet is huge, the MSR

cannot re-build the SIP fragment messages.

RTD54836

Description: The call cannot be established.

Condition: When configure the UDP as the SIP transport protocol, If the Packet is larger

than MTU-200, the transport protocol will automatically change to TCP, but if the

destination does not support TCP, the transport protocol cannot change back to UDP.

Resolved Problems in CMW520-E2206RTD54077

Description: The router will restart by exception.

Condition: Forwarding multicast packets incessantly through many subinterfaces.

RTD53933

Description: The route is not compatible with some brand of POS terminal device.

Condition: Work with some brand of POS terminal device.

RTD53990

Description: It shows as "dialer call-in * callback 2", with a parameter "2" unwanted,

while the function of callback works fine.

Condition: Configure "dialer call-in * callback" in Bri interface.

RTD53973

Description: After the call established, when the voice switches to the standard T.38

fax, the source-bind function will be unusable.

Condition: More than one interfaces can be used on router, use sip as the voip callsignal and the standard T.38 as the fax protocol, and configure the source-bind

command.


33/91

32

Resolved Problems in CMW520-E1908P02

RTD39984

Description: After reboot, the web login function through http will be disabled and

command "ip http enable" must be configured once again to enable it.

Condition: After enable CWMP, save the configuration and reboot the router.

Resolved Problems in CMW520-E1804

RTD31107

Description: The router forwards the packets to front-machine, and the front-machine

stop to send packets.

Condition:

When terminal unit sends soft-flowcontrol packets which including 0x11 or0x13 to the router.

RTD32332

Description: The DLSW connections can't be created successfully.

Condition: When DSLW create connections through sub Ethernet interface or

vlan-interface which work on bridge-forwarding mode.

ZDD01828

Description: The relay function failed.

Condition: ARP detection tries to work with DHCP relay function.

Resolved Problems in CMW520-B1707

RTD21682

Description: PPP will send negotiated packets from this interface anyway.

Condition: Running shutdown on BRI interface or physical interface of PRI, then

configuring ISDN Leased Line on it.

RTD21683

Description: the connection will always break down when 1 second is time out.

Condition: Configuring one Ethernet interface as PPPoE Client by pppoe-client

dial-bundle-number 101 idle-timeout 1, despite there are packets received during 1

second.

HSD33072

Description: The backup interface will flap (up/down) one time.


34/91

33

Condition: Reboot router when implemented the Interface-backup feature.

LSD26984

Description: The fallback authentication will not happen.

Condition: If the connect with the TACACS is lost.

RTD27056

Description: The tunnel can't up.

Condition: Implemented MPLS TE tunnel and keep the reservable-bandwidth equal to

tunnel BC0.


RTD21639

Description: RM will print some redundant information.

Condition: Input shutdown on one Encrypt interface.

RTD21642

Description: The statistic doesn‘t clean.

Condition: Enable IPV6 and configure IPV6 address on one interface, then get the

statistic of interface‘s packets after it received some IPV6 packets by display ipv6

interface XXX verbose. After that, reset ipv6 statistic and display ipv6 interface XXX

verbose again.

RTD20985

Description: System will print error info that PVC on the ATM interface has been

deleted.

Condition: Create PVC on the ATM interface and configure map bridge-group

broadcast on it, then configure atm-class and apply class on the interface.

RTD21516

Description: The reset operation will fail.

Condition: Configuring more than 4251 mboundarys on router ‘s interface, then reset

some of them with high speed packets received by the interface.

RTD21151

Description: The syntax of prompt info and debug info are not identical.

Condition: When dhcp-snooping is enable, print dhcp-snooping to get the prompt

info, then run undo dhcp-snooping and dhcp-snooping again, to get the debug info.


35/91

34

RTD21384

Description: When the client accesses the server with not idlesse, the server will always

disconnect it.

Condition: Configuring router as SFTP server, setting it‘s idle time by sftp server

idle-timeout several.

RTD21352

Description: The flow control is not shown in the result.

Condition: Enable flow control on GEC interface and get the info by display interface.

RTD21406

Description: It doesn‘t contain default value of transparent transmission on modem.

Condition: Get voice and fax default value by display voice default all.

RTD21577

Description: The default IP address by product will lose.

Condition: During the boot if the interface 0/0 is up.


RTD16324

Description: The router will reboot with exception notification.

Condition: To download software from FTP server to overwrite the file with same name.

RTD16521

Description: Ce as the NTP client can't synchronize with PE.

Condition: In the network of MPLS, to change the timer value of PE which is worked as

NTP server.

RTD17038

Description: The remote interface receives the loopback code and is set as mode of

loopback payload.

Condition: To set t1 x set fdl ansi on T1 channel of local side, and set t1 x set fdl att on

the same T1 channel of remote side, then sent loopback code on local side with

command t1 x sendloopcode fdl-ansi-payload-up.

RTD17152

Description: Telnet is failed.

Condition: Two routers are connected with transmission equipments and try to telnet

from the VLAN interfaces of the two routers.


36/91

35

RTD17375

Description: The call process will be failed.

Condition: Two routers are connected to each other with VE1 and VT1, to launch call

and delete R2 configuration of VE1 or VT1 on one router during call processing.

Resolved Problems in

CMW520-R1508P02&CMW520-B1508P02

RTD20541

Description: The calling will fail.

Condition: The calling number less than 6, and the Q931 section of SETUP message

from calling device does not include CALLED PARTY NUMBER and CALLing PARTY

NUMBER.

RTD19553

Description: The flow-control function doesn‘t take effect.

Condition: Configuring flow-control on the interface of SIC-1GEC, and send high

speed data to it.

RTD20307

Description: The value of entPhysicalSoftwareRev not matches the version number

exactly.

Condition: walk iso ---> mgmt ---> entityMIB ---> entPhysicalEntry --->

entPhysicalSoftwareRev‘s sub-node entPhysicalEntry and get value of

entPhysicalSoftwareRev by MIB Browser, then _display version to get the version

number.

Resolved Problems in

CMW520-R1508&CMW520-B1508

RTD18997

Description: The route will reboot.

Condition: The VE1 interface connected to switch with PRI signaling and received

FACILITY information from remote switch.

RTD18437

Description: The call cannot be established.


37/91

36

Condition: The user call a telephone with the VoIP system of H3C and the called

telephone has been set call forward.

RTD19880

Description: The data transmit forward by the ASE interface is error.

Condition: The user set reserve telnet and disable auto-negotiation.

RTD19991

Description: The default idle code is not 0x7e.

Condition: The 4BS interface works in the mode of BRI leased line.

RTD19852

Description: The user can not configure the router by com or telnet.

Condition: Using the English version of hyper terminal.


RTD18219

Description: The 2GE port halts receiving and transmitting data.

Condition: The mode of 2GE module is 100M/full duplex and forwards the packets. The

length of packets is random.


RTD13802

Description: The hookoff configuration in the FXO interface will lose.

Condition: Configuring ‗hookoff-time 36000‘ in a FXO interface and then resetting this

card.

RTD13055

Description: The configuration of Ioopback internal will be unsuccessful.

Condition: The user enables loopback-detection and configures ‗loopback internal‘in

a L2 port when stp function has been enabled.

RTD14199

Description: All commands can not be identified.

Condition: A sub-interface in an IMA-group has been set up. The user hot-plugs this

IMA card and then inserts it to the same slot.

HSD14531

Description: The information of DCD, DTR, DSR, RTS and CTS is error.


38/91

37

Condition: A DCE cable has been inserted in a SAE interface, but not connected to

remote terminal. The user configure asynchronous physical mode and display

information of this interface.

RTD15139

Description: VI(Visual Identity) modified from Huawei-3com to H3C.

Condition: None.

Resolved Problems in CMW520-B1501L01

RTD13013

Description: The information table for current calls (shown by command display voice

call-info) will not be clear.

Condition: Hunt-group function has been enabled when call connection is set up by

IVA(ISDN Voice Application) . The matched voice entity is unavailable.

Resolved Problems in CMW520-B1204P04

RTD12924

Description: The port will receive too many incorrect packets and 8E1 ports can not

work normally.

Condition: 8E1 ports communicate through fiber network. When one port‘s remote

fiber terminal is turned off.


RTD12559

Description: These packets can not be transmitted in VLAN.

Condition: The Ethernet L2 switching module receives ISIS Hello packets.

RTD12700

Description: The stream statistic doubles on the device, and the stream log is send to

XLOG server.

Condition: Applying Netstream on both inbound and outbound of one interface .


RTD12640

Description: VRRP can not support tracking MP-group ports.


39/91

38

Condition: Configuring VRRP on the MRS50 device.


RTD07017

Description: The grading will fail.

Condition: Upgrade the router by Quidview.

RTD11696

Description: The data can not be transmitted and the configuration on the VLAN will

lose.

Condition: Keeping data flux on 4FSW in MSR routers.

LSD08869

Description: It can not get IP address in the overdue pool.

Condition:

DHCP client has no IP address in free pool，but there is available IP address

in the overdue pool.

RTD11776

Description: The system will hint ‗OSPF Interface Not enabled‘.

Condition: The user configures network command in an ospf interface and then

displays this interface information.

RTD11378

Description: The value of TTL is error.

Condition: The user configures fast-forwarding by encryption cards and runs ping

command.

RTD11954

Description: The first calling number and the second one are not identical.

Condition: Enabling Radius and DPL, and then running one time dialing and two times

dialing operation.

RTD11646

Description: It can not set up ISIS.

Condition: Connecting MSR routers with Cisco devices, setting both interfaces‘ ISIS

type p2p and configuring bridge on MSR router ‘s interface.


40/91

39


RTD10154

Description: The interfaces states can not be up.

Condition: Connecting SIC-E1 interfaces between two MSR20 serious routers, and

enable using e1.


RTD11296

Description: Only the calling from the router to it‘s connecter is success, the other

direction calling is not normal.

Condition: configuring the router and it‘s connecter in G711U coding mode, andturning on VoIP.


HWD05620

Description: It can not boot.

Condition: Keeping one ESM and one VCPM on the MSR30-20.


RTD09176

Description: The call will fail.

Condition: Keeping on changing R2 country mode for a long time.

RTD09518

Description: The default value of dl-bits will not be renewed.

Condition: While configuring R2 CAS, if you execute follow commands in order: renew

0011, reverse 0101, undo renew, and undo reverse.

RTD07543

Description: That will result in the configuration of ATM-CLASS under this interface

invalid.

Condition: If you apply global ATM-CLASS under ATM interface, and configure

ATM-MAP under this interface‘s ATM-PVC view, then delete the ATM-MAP.


41/91

40

RTD09212

Description: The FTP server function on NAT can not work.

Condition: Configuring the IP address of WAN on the LAN server equaling to the

address of NAT‘ interface.

RTD10006

Description: The system will hint ‗Unable to open file‘.

Condition: The router is configured as TFTP client and PC as server . The user configures

a source file name with memory path.

RTD09918

Description: The default routing can not be deleted immediately.

Condition: Ripng default-route has been configured. The user deletes this

configuration and displays the routing information of Ripng.

RTD09832

Description: The voice bandwidth will loss and the call can not success.

Condition: If you configuring sequentially voice bandwidth and cir with equal value,

and then saving it and rebooting the router.


RTD09261

Description: After you input display mpls te cspf tedb node, the router will reboot.

Condition: Input command display mpls te cspf tedb node.

RTD08380

Description: When configuring ATM CLASS UBR on ATM-CLASS, if the parameter has

excess length, the parameter can work actually and the router will print abnormal info

and then reboot.

Condition: Input a parameter with excess length on the ATM service.

RTD08839

Description: Can not get correct statistic of some FTP packets.

Condition: Apply QoS on one port and match FTP packets, and then run DAR statistic.

RTD08764

Description: This port can not learn MAC address with learning state.

Condition: Enable STP and keeping one bridge port with learning state, and send

packets with different source MAC address to this port.


42/91

41

RTD08536

Description: The virtual VRRP MAC address can not be loaded on this port‘s MAC table

and then cause packets with it can not be transferred.

Condition: when the MAC tables is full on one port, and then apply VRP on it.

RTD08326

Description: VT‘s state will change up and down repeatedly.

Condition: Apply MPoFR on a 4E1 board, and transferring 10M speed data on it.

RTD06971

Condition: Configure DHCP under the interface view, and then change the

interface‘s IP address.

Description: All the configuration of DHCP on this interface wil l be lost.

Related Documentation

New Feature Documentation

None.

Documentation SetH3C MSR 20 Series Routers Installation Manual

H3C MSR 30 Series Routers Installation Manual


H3C MSR Series Routers Configuration Guide

H3C MSR Series Routers Command Reference

H3C MSR Series Routers Interface Card and Interface Module Manual

H3C MSR Series Routers OAP Module Manual

H3C MSR 20-1X Routers Installation Manual

H3C MSR Series Routers Web-Based Configuration Manual

H3C MSR 20-1X Routers Quick Start

H3C MSR 30-1X Routers Quick Start


Obtaining DocumentationTake the following steps to get related documents from the H3C website at www.h3c.com.

1. Go to http://www.h3c.com/portal/Technical_Documents.


43/91

42

2. Choose the desired product category and model.

Technical support

[email protected]

http://www.h3c.com


44/91

43

Appendix A Feature List

Hardware FeaturesTable 5 MSR20-1X Series Hardware Features

ItemMSR 20-10Description

MSR 20-11Description




Dimensions (H x W

x D)

44.2mm300

mm240mm

44.2mm300

mm240mm

44.2mm300

mm240mm

44.2mm300

mm240mm

44.2mm300

mm240mm

Weight 3Kg 3Kg 3Kg 3Kg 3Kg

Input AC voltage

Rated voltage: 100 VAC to 240 VAC;

50 Hz/60 Hz

Input DC voltage Not support DC

Max power 25W

Operating

temperature0°C to 40°C

Relative humidity

(noncondensing)5% to 90%

Processor PowerPC PowerPC PowerPC PowerPC PowerPC

BootROM 1MB 1MB 1MB 1MB 1MB

FLASH 16MB/32 MB 16MB/32 MB 16MB/32 MB 16MB/32 MB 16MB/32 MB

Memory 256MB 256MB 256MB 256MB 256MB

Externa

l

modul

e

SIC/

DSIC

module

1 1 1 1 1

Internal

modul

e

VPM

strip0 0 1 0 1

Fixed

interfa

ce

Consol

e/AUX1 1 1 1 1

USB 1 1 1 1 1

FE1 electrical

interfaces

1 electrical

interfaces

1 electrical

interfaces

1 electrical

interfaces

1 electrical

interfaces

FE

switchi

ng

interfac

e

4 4 4 4 4

ADSL 0 0 0 0 1

G.SHDS 0 0 0 1(G.SHDSL.bis 0


45/91

44

L )

SAE 0 1 0 0 0

ISDN

S/T0 0 0 1 1

AM 0 0 0 0 1

E1/T1 0 0 1 0 0

option

alWlan 1 0 1 1 1

Table 6 MSR20 Series Hardware Features

ItemMSR 20-20Description



Dimensions (H x W x

D)

44.2mm360mm287.

1mm

44.2mm360mm28

7.1mm

44.2mm442mm407.1

mm

Weight 3.4Kg 3.4Kg 5.4Kg

Input AC voltage Rated voltage: 100 VAC to 240 VAC; 50/60 Hz

Input DC vo