Upload
buitruc
View
220
Download
0
Embed Size (px)
Citation preview
Manual de Instruções para Bombas de Direção Vetus e BCS
Em caso dúvidas na instalação após a leitura do manual, favor entrar em
contato com nosso departamento técnico através do telefone ou email:
• (11) 3477-5655�
• email: [email protected]
Horários de atendimento:
Segunda-feira à quinta-feira: 8h – 18h
Sexta-feira: 8h – 17h
Rua Anhaia 982, Bom Retiro – SP
www.marineoffice.com.br
Stuurpompen
Steering pumps
Steuerpumpen
Pompe de commande
Bomba de dirección
Pompa di governo
Copyr ight © 2003, 2004 Vetus den Ouden n.v. Schiedam Hol land
Installatieinstructies
Installation instructions
Installationsanweisungen
Instructions d’installation
Instrucciones deinstalación
Istruzioni perl’installazione
HTP20HTP30HTP42
HTP20RHTP30RHTP42R
4 2.0114 Steering pumps HTP20(R), HTP30(R), HTP42(R)
Introduction
This manual relates to Vetus steering pumps, types HTP20(R), HTP30(R) and HTP42(R).
This manual is a supplement to the manual supplied with the cylinder. (2.0105 I.H30-175,or 2.0113 I.OB300)
Note:The Vetus EHP type ‘R’ is already equipped with a built-in check valve.
Fitting
Steering pumpThe filler cap and balance tube* must always be on top of the unit, at the highest point.
*) When more than one pump is fitted, all oil reservoirs must be connected by balancetubes.
The pump may be installed in any positionbetween horizontal and vertical.
Fit the threaded rod supplied into the steering pump using Loctite®.
The steering pump is supplied with a filler cap without air holes as standard. If necessary,this can be replaced by the filler capwith air holes also supplied.
With double operation, check that the lowest steering pump is fitted with a filler cap with-out a hole.
90˚
2.0114 5Steering pumps HTP20(R), HTP30(R), HTP42(R)
Oil Expansion TankIf an oil expansion tank is fitted, fit filler caps without air holes in all steering pumps.
Connections
A, B Cylinderconnections
C Balance tubeconnection
Technical Data
Steering pump : HTP20(R) HTP30(R) HTP42(R)Type : Axial plunger pumpNumber of plungers : 5 5 7Capacity : 19,7 cm3/rev. 30,0 cm3/rev. 42,0 cm3/rev.
(1.2 cu.inch/rev.) (1.8 cu.inch/rev.) (2.6 cu.inch/rev.)Operating pressure : max. 40 bar (570 psi, 3923 kPa), at ø 8 mm tube diameter
max. 56 bar (797 psi, 5492 kPa), at ø 10 mm tube diameterConnections : G 1/4 female threadFiller cap : G 3/8 female threadWeight,without built-innon-return valve : 3.3 kg (7.3 lbs) 3.3 kg (7.3 lbs) 3.3 kg (7.3 lbs)with built-innon-return valve : 4.1 kg (9.0 lbs) 4.1 kg (9.0 lbs) 4.1 kg (9.0 lbs)Maximum wheeldiameter : 38 cm (1.5”) 38 cm (1.5”) 53 cm (2”)Pressure relief valve, only by pumps with buit-in non-return valveSetting : 60 bar (870 psi, 6000 kPa),
at ø 8 mm tube diameter70 bar (1015 psi, 7000 kPa), at ø 10 mm tube diameter
HTP HTPR
A B
C
C
C
CBA
ENGLISH
14 2.0114 Steering pumps HTP20(R), HTP30(R), HTP42(R)
Hoofdafmetingen Hauptabmessungen Dimensiones principales
Principal dimensions Dimensions principales Dimensioni principali
ø 7
(4x) HTP
ø 86
p.c.d. 95
96
R11
ø 7
(4x) HTPR
ø 86
p.c.d. 95
BoormalDrill patternBohrschabloneGabaritPlantilla de perforaciónSagoma di trapana natura
BoormalDrill patternBohrschabloneGabaritPlantilla de perforaciónSagoma di trapana natura
2.0114 15Steering pumps HTP20(R), HTP30(R), HTP42(R)
22 107
181
52
HTP
ø 3/4"1:12
M6
ø 11
5
ø 3/4"1:12
M6
107 52
ø 11
5 HTPR
69
228
67
67
67
67
HTP20, HTP30, HTP42
HTP20R, HTP30R, HTP42R
Hoofdafmetingen Hauptabmessungen Dimensiones principales
Principal dimensions Dimensions principales Dimensioni principali
Printed in the Netherlands2.0114 I.HTPR 10-03 Rev. 02-04
FOKKERSTRAAT 571 - 3125 BD SCHIEDAM - HOLLAND - TEL.: +31 10 4377700 - TELEX: 23470TELEFAX: +31 10 4372673 - 4621286 - E-MAIL: [email protected] - INTERNET: http://www.vetus.nl